Jump to content
SAU Community

Recommended Posts

Being built by advanced and tuned by JEM I doubt anyone will question the numbers.

Interesting about the breather being normal for that power level, not something I expected.

Being built by advanced and tuned by JEM I doubt anyone will question the numbers.

Interesting about the breather being normal for that power level, not something I expected.

Because u dont normally see it.

Out of site out of mind :)

It's the catch can breather.

For anyone possibly doubting the numbers, it ran 10.7@147mph at WSID with 490rwk. Next time out with 536rwk should do 150mph+

The car is also on the Motive 16 Drag battle DVD.

I'm questioning the numbers! That was 10.2@147 not 10.7! :)

Being built by advanced and tuned by JEM I doubt anyone will question the numbers.

Interesting about the breather being normal for that power level, not something I expected.

This was the first thing I noticed as well

Seems odd to keep pulling those numbers with that happening

It was mainly in relation to that...

I'm questioning the numbers! That was 10.2@147 not 10.7! :)

Yeah I wasn't sure if it was 10.7 or 10.2 :D

Edited by SRS13
  • 2 weeks later...

I might be selling my 5858 BB turbo. Brand new, box hasn't even been opened!! After $1450 for it.

Thinking about going bigger (6262) as the engine being built will need a bigger turbo!

If interested PM me.

Edited by SRS13
  • 2 weeks later...

Finally got some numbers but its not done yet,

On the New motor, with the 6262 .84 TS BB CEA.

Run-in tune (super safe) verylow/negative timing, 9-10 psi. 210-220 rwkw.

Turbo is super responsive and perky even with the timing so low, I noticed instantly its very throttle responsive, its very possible my intake setup helps in this regard. But the way it moves the air so quickly I have a good feeling this setup will be pretty decent on the 30/25 with vct!

One noticable characteristic.. the turbo seems very loud. even on low boost. however i am moving from lowmount to high mount during this build, so that might be why i think that.

will be doing real tuning next week if all continues well. Will post numbers as promised when its done. Unfortunently still running hte PFC and Tomei Z32 as no one has purchased the gear yet.

-dale

Edited by SilverECR33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...