Jump to content
SAU Community

Recommended Posts

6 hours ago, Buraz said:

What's everyone's results with 6262 precision??

My is out of puff at just under 440kw and 26 psi on a 2.8l stroker

Mine has gone 560kw at the hubs. 440kw sounds significantly lower regardless of the dyno. Got a graph? Any restrictions?

Ahhh okay!! That's a big difference for sure. No restrictions whatsoever, it's a split pulse 6 boost and twin gates too. 17.5psi springs!!

 

Car hammers no doubt about it and I'm more than happy. Just thought I'd share my results with you guys and see other results

Oh wow that's a massive difference!! Is it same rear housing as mine?? After talking to a few people now, this thing is only a tiny turbo and tell me it's about right.
But yours is an unbelievable result. Still a 2.6?

  • 5 weeks later...

Mine should be hitting the dyno next week hopefully 

previous tune was 645kw at 34psi with a 7175 gt42 on a hks 2.8

few changes since last tune such as 100mm plazmaman cooler and turbo1 custom twin scroll manifold with twin 38mm tial gates,

should come on nicer now then it did with the old greddy stainless manifold

  • Like 2
  • 1 month later...
On ‎25‎/‎05‎/‎2017 at 10:04 PM, SiR_RB said:

Mine should be hitting the dyno next week hopefully 

previous tune was 645kw at 34psi with a 7175 gt42 on a hks 2.8

few changes since last tune such as 100mm plazmaman cooler and turbo1 custom twin scroll manifold with twin 38mm tial gates,

should come on nicer now then it did with the old greddy stainless manifold

How did it go?

I am quite interested to see how much difference a manifold makes.

I have a 6766 on a T88 Greddy manifold and have access to a 6 boost if the need arises. The car makes 460 odd rwkw @30psi on Unigroups dyno and traps 138mph but I still want more.

Have been told I should have gone the 6466 as its better suited to an RB26

Edited by ido09s
On 26/06/2017 at 11:22 PM, SimonR32 said:

The 6262 sillyness is never ending... New cams just got the most power and torque it's ever made

20170626_145138_zpswxu7yhfh.jpg

Lol what..

760 awhp on a turbo rated to 705hp.. not questioning your results but that is going to be overspeeding by like 30%

 

Very impressive that it's still happy pushed that hard. I'm interested in your exhaust back pressure and compressor outlet temp numbers.

Dynapack hubber gives a possible 5-10% inflated reading.. However simons back to back results with his setup and different cam combos are awesome and the car speaks for itself performance wise.. 

Its unfortunate that the next time its dynoed it wont be a true back to back unless you can sweet talk sean and he has access to the dyno still

 

Edited by azzada1
6 hours ago, burn4005 said:

Lol what..

760 awhp on a turbo rated to 705hp.. not questioning your results but that is going to be overspeeding by like 30%

 

Very impressive that it's still happy pushed that hard. I'm interested in your exhaust back pressure and compressor outlet temp numbers.

Technically it's rear hub hp, not awhp. I don't think they have an overspeed (it's not an EFR after all)

Turning the dyno on SAE correction it shows up 797hp so god knows how much it's making at the flywheel but definitely more than the turbo is rated at. Never measured backpressure in exhaust but air temps after the intercooler are more than reasonable

30 minutes ago, SimonR32 said:

Technically it's rear hub hp, not awhp. I don't think they have an overspeed (it's not an EFR after all)

Turning the dyno on SAE correction it shows up 797hp so god knows how much it's making at the flywheel but definitely more than the turbo is rated at. Never measured backpressure in exhaust but air temps after the intercooler are more than reasonable

its frustrating that no compressor maps are available for precisions because a turbo compressor power rating is usually based on an efficiency below 58% or even the stonewall flow (flow choke) of the compressor. this is the speed that part of the assembly reaches sonic speed and flow basically cannot be increased any further by spinning it faster or altering the downstream pressure. thats why the choke line is vertical in a compressor map. (although note that maps from garret state efficiency below 58% is the end of their displayed map, and they consider that point "overspeeding") It's not necessarily when it wants to fall apart, but the efficiency falls over and then finally the compressor won't flow any more due to sonic shock waves inside the compressor inlet or volute causing a choked flow condition.

its interesting that the Precisions seem to be happy well past the flow the manufacturer rates the compressor for. whereas Borg Warner made their turbines strong enough to cope with the choke speed of the compressor they paired it with and not much more as its outside the design parameters.

Edited by burn4005
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...