Jump to content
SAU Community

Recommended Posts

I'm doing some research for a planned build.

Decided i'd take a rwd 26/30dett route.

I've had a bit of a browse through this section and see mixed reports when it comes to finding good rb30 blocks to use.

Does anyone have any recommendations, or is it just a case of luck of the draw?

If theres is a source of good condition blocks, anyone have an average price?

Had a look, no mention of just the blocks, only assembled bottom ends, its the same with rips.

Ideally i'd like to pick up an xrayed and cleaned block i could get on with the buld with (boring etc etc to be done much much later)

you pay about 100 to 200 for them. i got my one for free off some dude off the vl website. gave me full motor and gearbox and all the stuff. there not really worth anything. i doubt youd get many that wont be useable. there generally pretty good still with hone marks after 300000kms and stuff. if it happens to be out of round it will be fixed if you bore it out. think it cost me 60 to hone it and 180 or 250 or something to get it bored out. some wreckers want 330 for them but one guy said he gets them for 150 all the time.

put up a wanted ad on here and any other websites you know and you should get one pretty quick

No one is going to spend the money/time checking out a block just to sell it as is, they will then assemble and sell that way.

just buy a block for $100-$250 and spend your own money getting it checked. I can't see it working the way you want unfortunately.

Had a look, no mention of just the blocks, only assembled bottom ends, its the same with rips.

Ideally i'd like to pick up an xrayed and cleaned block i could get on with the buld with (boring etc etc to be done much much later)

Sorry to be the bearer of bad news, but you'll never find one like that at the price you want to pay.

As Ash said, go get a block and do the work yourself :thumbsup:

Nice :) well for the money mentioned above i have no problems buying a few if the fiorst doeasnt work out.

I was just worried they might cost a bit and have a high risk of being busticated.

As a general rule i dont mind spending up where its a smart move, i just hate the idea of spending lots for a unknown quantity.

With what you've all said... i think its time to go shopping.

yeah it does happen, there are some bad ones out there. the first one for my stagea was cracked, didn't find out until it was xrayed.

fortunately in my case the workshop supplying it replaced it. but even so its only a couple of hundred if it doesn't work out

r31's are about 500 bux

you get an engine with the car

hmmm thats a thought... it could give me someplace to put the rb25 that i'll be putting out of a home.

more seriously, your spot on with this, and it looks like a good option. it would mean i need a bit more kit to get going.

I'd need a crane to pull the engine then i'd need to figure out how to get rid of the body quick afterwards (not alot of room here).

but atleast now i kinda have a plan and i can get cracking.

I'm doing a search, but while i'm at it, can anyone recommend a good engine stand??

yeah get one rated to more than just the basic

this style: 80.jpg

not this style:80.jpg

these motors are damn long and damn heavy. and make sure you've got good bolts with plenty of thread to connect the motor to the stand

yeah get one rated to more than just the basic

this style: 80.jpg

not this style:80.jpg

these motors are damn long and damn heavy. and make sure you've got good bolts with plenty of thread to connect the motor to the stand

agreed, if your buying a cheapie, the 4 legged buggers are the way to go, if your willing to spend the coin... Bluepoint makes a wicked collapseable 3 legger. 

they hold the rb motors very very easil, i also have one of those 3 legger cheapies... i only use it when i know i dont have to move the motor around as i dont trust it much even tho it hasnt buckled or anything with a motor sitting on it for about 3-4months straight. even with blankets and other shit thrown over it 

i only use an engine hoist, then once the engine is removed from the car i place the engine on the ground on 2 layers of thick carpet.

working on the donk on a stand would be easier BUT it wont fall far if its already on the ground :down: simply sit on the floor and start stripping it down

Problem with it being on the ground is after half a day your lower back will be screaming at you

No it doesn't as you're sitting beside it. When on the stand you're bending down and your back hates you. The last few I've done on the ground, the next one is getting a stand as I want to be able to put it up side down easily.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
×
×
  • Create New...