Jump to content
SAU Community

Recommended Posts

hey guys,

Ive been reading about power bands lately, and its apparently quite important to know your cars when it comes to racing especially in the case of a naturally aspirated car.

My question is, how do you know what your power band is? Is it just drive and feel it for yourself or does each car have a power band that any common car owner can tell you?

I've also wondered about when racing, is it best to shift out of first at say 4 rpm and then build the revs in the higher gears or is it better to rev it higher in first? I feel like when I rev high in first im not really getting as much power as if I let it rev in second, and I just feeling the wrong thing?

I've never actually looked at the speedo while testing all this as im worried about keeping my eyes off the road.

Any help is greatly appreciated, one of my friends beat me in his celica the other day and all the stats show that my car should have won if my technique was better, so im trying my best to better understand everything.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/318812-power-band/
Share on other sites

The RPM where you feel your car pulling is where the power band is. Look at horsepower and torque curves (dyno graphs) on google and you will see exactly what a power band looks like. You will want to launch your car with your engine revved such that after the clutch grabs the needle drops to around the RPM where the torque curve for your car shows it is a constant level (not where it is rising steeply) so you get a strong pull at takeoff. Does that make sense?

High revving lower displacement engines such as VTECs have the peaky power (in the top end of the RPM range) but larger displacement N/A engines can have more torque in the low end too (i.e. Nissan 350z/370z).

Link to comment
https://www.sau.com.au/forums/topic/318812-power-band/#findComment-5219785
Share on other sites

having been on track on 2 stroke road bikes i can tell you changing gears is pretty much the same no matter what your in/on. you want to shift from first into second only when doing so will result in more acceleration, for 99% of vehicles this means changing at redline. with actual 2 stroke machines with proper powerband, changing early can result in having almost no power as they often only make any real power in the top 20% of their rev range. as to a good launch, as much as it may kill your clutch, to do a perfect launch on the bike i would simply give it full throttle at take off and slip the clutch out keeping the revs at around 12k (where the bike its max power). not 100% on doing this in a car but definitely the way to go on the bike.

Link to comment
https://www.sau.com.au/forums/topic/318812-power-band/#findComment-5223193
Share on other sites

  • 3 weeks later...

i've read in a couple of places that the powerband can be shifted by changing cams or using cam gears, how does this work?

when it comes to changing gears, it depends when your car falls off its power band, this may be at 6500, or (more likely) much higher, like 8000rpm.

think of the power curve of the engine, you always want to be accelerating as hard as possible, so if you change at 4000rpm you're missing out on 4000-7000rpm goodness, which is where most of the power is. theoretically, the higher the rpm, the more explosions per second, the more power, but all sorts of efficiency issues get in the way. still, higher rpm = higher power. in f1 when they want to dial back the power to save the engine/fuel, they turn it's redline down.

Link to comment
https://www.sau.com.au/forums/topic/318812-power-band/#findComment-5266924
Share on other sites

Generally - the larger the cams, the more revs are needed to get the engine to make power e.g at set of 280deg 11mm lift cams on an RB25DE would need 4500-5000rpm before it started to make power, below that the airflow through the ports is very slow and inefficiant, So you then need to rev the engine harder eg 9000rpm redline in order to have a decent power band, if the engine only revved to 7000, you would only have 2000rpm where the engine makes any grunt, so each time you changed gear you would drop out of the power and go no where.

Think of big cams like you would a big turbo...kinda

Link to comment
https://www.sau.com.au/forums/topic/318812-power-band/#findComment-5266947
Share on other sites

i've read in a couple of places that the powerband can be shifted by changing cams or using cam gears, how does this work?

when it comes to changing gears, it depends when your car falls off its power band, this may be at 6500, or (more likely) much higher, like 8000rpm.

think of the power curve of the engine, you always want to be accelerating as hard as possible, so if you change at 4000rpm you're missing out on 4000-7000rpm goodness, which is where most of the power is. theoretically, the higher the rpm, the more explosions per second, the more power, but all sorts of efficiency issues get in the way. still, higher rpm = higher power. in f1 when they want to dial back the power to save the engine/fuel, they turn it's redline down.

also you are missing out on 3000rpm of accelerating in a lower gear with an easier ratio. that is where the argument of "what rpm to change gears at" starts to get a bit more complicated. a simple view is to change gears the moment you get past the peak power output. what this doesn't take into account is that even though the power may be dropping off, it may still be higher than at the rpm you will be at in the next gear. and then as i said above, the more time you spend in the lower gear (within reason), the easier the car will accelerate, especially when you are talking about the higher gears. that is where each car needs to be evaluated individually to see what works best. i know that in the case of the missus SSS pulsar, with the stock headers it would start to choke around 5500rpm, and it was pretty much pointless to rev it past 6500rpm. put on a set of extractors and it doesn't start to choke until about 6500rpm but will still pull all the way to the 7500rpm redline.

Link to comment
https://www.sau.com.au/forums/topic/318812-power-band/#findComment-5267237
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...