Jump to content
SAU Community

Recommended Posts

yeah celica for me personally... it's just so fvking TOUGH!!!

there used to be (probably still is) a celica TA22 in maroon that used to drive to work next to me... nearly had a few accidents could never take my eyes off it

looked sooooo well maintained / resto'd

I've got 3 TA22 Celicas, one a genuine GT...one an LT with GT engine and another factory LT. In love with em! I've been wanting to do a chop top on one of them with SR20 conversion to boot...bit sacreligious, but fark it would be a fun car.

We also used to have an Aussie (apparently one of three, ex Toyota exec vehicles) delivered, yellow RA28 GT...got written off in a targa race :P buuut we still have the build plates...and several sections of it lol.

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

I've got 3 TA22 Celicas, one a genuine GT...one an LT with GT engine and another factory LT. In love with em! I've been wanting to do a chop top on one of them with SR20 conversion to boot...bit sacreligious, but fark it would be a fun car.

We also used to have an Aussie (apparently one of three, ex Toyota exec vehicles) delivered, yellow RA28 GT...got written off in a targa race :( buuut we still have the build plates...and several sections of it lol.

Pics!

my dick is no longer bound by the constraints of my pants.

thank you.

PS - if stock, 2000gt ftw. modified i'd have to go with gtr or Z, only because i've never seen a modified 2000gt (understandabe with the price of the things)

Edited by VB-
Pics!
Stop F#*ing us around Birds and post the pics!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! :(

:P

PLEASE????? :P

LOL sorry I didn't know you guys were obsessed avid Toyota fans, I thought we were all Nissan fanboys on these forums :P

I'll scan in a couple 35mm prints of the RA28 tomorrow. The TA22s are under car covers, but here's one of them during the restoration process:

2q0822h.jpg

zx79dy.jpg

This was back when Yamaha made heads (f***ing good heads at that) instead of keyboards :P

And Weber 45s meant alot of power, not a roast barbeque and calibre of gun!

These babys have a miniature V8 sound with a decent exhaust.

Would you like a tweed jacket with that Shan :bunny:

Real men drive these!

your concept of a real man couldn't afford a Toyota 2000GT :D They're that rare and sought after.

LOL sorry I didn't know you guys were obsessed avid Toyota fans, I thought we were all Nissan fanboys on these forums :bunny:

As a genuine car enthusiast, I appreciate all good cars. I'm not one of these knobs that thinks one make or model is the be all and end all like some people on these forums think.

Every car has it's strengths and weaknesses and no one make has made the perfect car (despite what the R35 blokes think).

Great pics Birds, also DOOOO IIIITTTT, SR20 it lol

datsun 1200 you can get them here... 120y coupe is different model... not as pretty.

Agreed they did something weird to the back of them that just never looked right.

120Y sedan for the win i might be a bit biased though lol.

post-54017-1274926778_thumb.jpg

As a genuine car enthusiast, I appreciate all good cars. I'm not one of these knobs that thinks one make or model is the be all and end all like some people on these forums think.

Every car has it's strengths and weaknesses and no one make has made the perfect car (despite what the R35 blokes think).

Great pics Birds, also DOOOO IIIITTTT, SR20 it lol

A true enthusiast and not just a fan :bunny:

This baby would be worth a mint if we still had it - 1 of 3 in Australia (apparently):

ws5kx1.jpg

ei4gn7.jpg

Bottom left, one of our Targa Tasmania prepped Celicas (and no, that is not me in the photo lol):

10z1iqg.jpg

Careful! Don't want this thread being deleted for pornography!

Birds: Tragic to hear it's gone!

rgr34: How does it treat you as a daily?

the car serves as a great daily more modern motor helps me keep up with modern traffic. it hasnt upset the cars handling etc... its revs hard and being quite light goes alot better than some newer :blink: modern small cars... good on fuel etc...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
×
×
  • Create New...