Jump to content
SAU Community

Recommended Posts

I've done lots of searching both here and on other forums so I apologise in advance if the correct answer is out there.

So far I've found quotes that the standard R34GTT NEO injectors are 340cc,350cc,370cc or 380cc.

Can anyone say for certain what size they are? I think that I might be reaching the limit of mine as I have injector duration of 20-22m/s at full throttle.

My S2 Stagea is running FMIC, std turbo (soon to be replaced with hybrid) 80mm cat back,silenced decat,apexi induction kit, Gizzmo EBC set at 0.75bar boost and Walbro 255lph fuel pump.

Edited by DeanR33
Link to comment
https://www.sau.com.au/forums/topic/324899-r34-gtt-std-injector-size-please/
Share on other sites

well the r33 injectors are 370cc and from what i am aware the r34 is the same size (not 100% sure on that though).

if you are reaching the limit of the injectors with only 11psi then there is something going on. either your fuel pump is stuffed, fuel filter is blocked or the fuel pressure reg is stuffed. not sure what 20ms is in % of injector duty. generally about 250kw is the max for stock injectors.

I'm maxing out my nismo 480cc's at 240kw, so i'm pretty sure my stock 370cc injectors would not have got that far...

Yes 34 is definetly 370cc!

There's definitely been people on this forum finding 220rwkw on the standard 370cc, but I'd understood that was the limit without increasing the base fuel pressure. I'd also always understood the nismo 480cc injectors to be roughly good for 480hp at the engine and 280+rwkw?

(480hp = 357.9kw .. take 20% drivetrain loss - 286.32rwkw)

Can anyone else confirm their experiences?

I always thought that they were 370 or 380cc, but I posed the same question on Skylineowners.com and someone on there swears that they are either 330 or 340cc, which amazes me considering the regular rb25det ones are known to be 370cc.

If they are 330cc then I must be getting pretty close to needing uprated ones.

To be honest with all the knowledge on here I thought someone would be able to give a definate answer.

Curious as to what these are worth second hand?

And I have read that the nismo 480cc running around 280rwkw on safe tunes in the power thread. Well I hope that is the case as that's what I have bought to support my GT3071R upgrade :thumbsup:

Well, i had these 480cc's running with my original turbo, then when i upgraded to a hks 2835 my tuner said they was my limiting factor for not pushing more boost through (only tuned to 13psi)....

chrisr34gtt that was pretty much the reason i got them too, i was aiming for the 280kw mark and thought it would be achievable with those injectors. Will now have to fork out for new ones if i want an increase! :P

  • 3 years later...
  • 2 weeks later...

The GTR's run 11mm top Orings, and a square large lower Oring. They won't fit without some buchery. What are you after size wise?

The NEO injectors were carried over into the VQ25det's also, as they are exactly the same.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
×
×
  • Create New...