Jump to content
SAU Community

Recommended Posts

Hi fellow motorsport guru's,

I'm thinking about getting full slicks for next year's supersprint season and there are so many brands out there, I don't know where to begin.

I've never driven on them before, only driven on various semi slicks so anyone with experience with slicks could give me some advice?

What brands offer best value for money?

Which ones would be best suited to 3-5 lap supersprints?

Any changes I need to make to the car suspension/set up wise?

Special care or air pressure required?

In the supersprint series, I notice people running Avon and Michelin, but haven't noticed others. I believe Kumho, Hoosier and Dunlop offer slicks as well.

I have 17 x 9 inch wheels on all four corners so can run the same size tyres front and rear and car is S13 Silvia.

P.S. On a tight budget so hopefully can find something for under $1500

Regards

Mark

Edited by nismoman
Link to comment
https://www.sau.com.au/forums/topic/325364-full-slick-racing-tyres/
Share on other sites

I don't believe slicks really are well suited to 3-5 lap supersprints. But if you do get some, get soft compounds. I bought some medium compound Kumho slicks because they were on special, and it takes the best part of 2 laps just to get them working properly. Any semi I've had has been pretty well good to go after the warm up lap. I think a good semi (DZ03 or A050) would be faster than my medium compound slicks if its a single lap time you want.

my experience on slicks is limited to mostly dunlop and michelien but have used avon and khumo a couple of times too.

micheleins are pretty good and I would rate them over the dunlops. they are the favoured tyre in a number of aus categories which makes them easy to get too. we had to use dunlops a few times as the event sponsor tyre and they were not as fast as the micheleins, didn't last as long as cost a bit more from memory.

set-up wise you will find you can go up a fair way in spring rate as you now have plenty of grip. if you set-up is too soft all that grip will just end with lots of body roll.

like harry said a new semi will not be far off for outright lap pace but the slicks do hold up better to longer stints.

my experience on slicks is limited to mostly dunlop and michelien but have used avon and khumo a couple of times too.

micheleins are pretty good and I would rate them over the dunlops. they are the favoured tyre in a number of aus categories which makes them easy to get too. we had to use dunlops a few times as the event sponsor tyre and they were not as fast as the micheleins, didn't last as long as cost a bit more from memory.

set-up wise you will find you can go up a fair way in spring rate as you now have plenty of grip. if you set-up is too soft all that grip will just end with lots of body roll.

like harry said a new semi will not be far off for outright lap pace but the slicks do hold up better to longer stints.

any idea on what spring rates to go for rich?

ive got some dunlop formula Rs to go on my car.

sorry about the thread jack

another thing worth mentioning is that slicks apparrently are less tolerant of heat cycling than semis.

I haven't had mine long enough to realy form an opinion on that, but I can say the first time I used the slicks running the same 6/4kg springs I used with the semis I could not break traction in 3rd gear corners at Lakeside where I'm usually sideways... Not even close - no matter how aggressive you were - it would just grip and understeer.. It was like driving an EVO! Second time I used them I changed spring rates to 7/6kg and had traction issues in 4th on straights, let alone 3rd gear corners! Was that solely due to the 50% higher rear spring rate, or was it also due to less tyre grip compared to the previous meeting? I don't know, but I suspect it's at least a little from column B...

any idea on what spring rates to go for rich?

ive got some dunlop formula Rs to go on my car.

sorry about the thread jack

it's really a bit of trial and error with the spring rates. but if you are happy with them now on semis i'd definitely go up at least 20% in rate front and rear for the slicks. best to talk to someone who has a good handle on setting up a big, powerful, RWD car on slicks though. it's not as simple as 1 size fits all. :P

harry's experience is pretty much what happens. you find a car that felt nice and 'sharp' and 'pointy' on semis suddenly has heaps of rear end grip on slicks and so much mid corner grip the thing rolls like a pig and just wants to push understeer when you are on the power. more spring helps a lot.

I guess I'm after a tyre that will give me the best lap time but also a bit of longevity. The sprints I'm in consist of 1 warm up lap, then 3 hot ones and 1 warm down.

With that format I thought a full slick could be brought up to temperature and bang out a quicker time than semi's.

I don't like the sound of slicks going off after a handful of heat cycles though... Don't want to be left with hard as nails slicks after two events.

Could it be true that the Advan A050's are the ultimate sprint tyre for quick lap times? Over a slick even?

Edited by nismoman

Hey Mark,

I'm no expert but i have used a slick tyre for supersprints at Oran park (Avon's) a few yrs back they were off a BMW M3, and they were fine with one warm up lap and then two laps,I guess it all depends on the slick compound,weight of the car and your hp at the wheels. If you are going to compete in a class of racing be sure that using a full slick doesn't put into another category. I would talk to a reputable race tyre reseller on what would suit your vehicle best,oh and yes you do play with tyre pressures a little, if your in Sydney try talking to the guy out at Gordon Levin tyres in Emu Plains, they used to have a separate race tyre division there.Cheers have fun.

Carlo

I honestly think its a bad idea.

Superlap showed perfectly clearly that soft semi slicks are literally seconds a lap quicker than medium or hard slicks. So don't move to them expecting better performance.

You only get 3 laps and about 5 sessions. Medium or soft semis will last 2 or 3 days, wet or dry and you will go faster. And after all that is the only name of the game in supersprints.

I do run slicks sometimes but I always take spare wheels with treaded tyres. And if you only uses treaded tyres when it rains it will be years before they wear out (ie you will throw them away first).

Personally, I would grab soft or medium/soft semis for competition. Then a set of second wheels that fit a common second hand slick size for practice and open days.

I guess I'm after a tyre that will give me the best lap time but also a bit of longevity. The sprints I'm in consist of 1 warm up lap, then 3 hot ones and 1 warm down.

With that format I thought a full slick could be brought up to temperature and bang out a quicker time than semi's.

I don't like the sound of slicks going off after a handful of heat cycles though... Don't want to be left with hard as nails slicks after two events.

Could it be true that the Advan A050's are the ultimate sprint tyre for quick lap times? Over a slick even?

Mark the r35's go well on the 2nd hand michelin gt series slicks (they are s9's - hard compound) they take a lap or to to come on. They are very exxy new but very cheap 2nd hand (we usually get about two sprints from a 2nd hand set) anyway we run the 270/68's but you may be looking at the 240's to fit your car (do you run 18's?) They have worked for us and are faster than semi's on our cars. A certain someone will be running softer michelins this weekend (s7's) i am sure it means i will be pipped by my good mate, he'll run a 1:01.xx - if you end up running michelins talk to marek and i we have some advice re pressures and heat cycles for these.

What is it with you guys and full slicks.

The basic ethos of time attack is built solely around mad lap dashes on SEMI SLICKS.

Its what sets it apart from circuit racing. Am i missing something or are you all going door to door circuit racing ?

What is it with you guys and full slicks.

The basic ethos of time attack is built solely around mad lap dashes on SEMI SLICKS.

Its what sets it apart from circuit racing. Am i missing something or are you all going door to door circuit racing ?

Noel,,,we are not running time attack we are running State supersprints and the rules allow you to run slicks. Actually i think time attack organizers should go along to a meeting and see how its run and the rules we run under. They may well learn how to run an event properly.

Cheers

Neil.

What is it with you guys and full slicks.

The basic ethos of time attack is built solely around mad lap dashes on SEMI SLICKS.

Its what sets it apart from circuit racing. Am i missing something or are you all going door to door circuit racing ?

If we had a proper Timeattack event here in QLD I would stay on the semis for that. I will continue to use RE55s or whatver I can get my hands on seems they have dissapeared but plan on moving to slicks for a little bit of circuit racing in the Top Gear racing series at QR... :D

:D

What is it with you guys and full slicks.

The basic ethos of time attack is built solely around mad lap dashes on SEMI SLICKS.

Its what sets it apart from circuit racing. Am i missing something or are you all going door to door circuit racing ?

err, i just want to go fast and have fun. i didnt realise there was an 'ethos' we had to adhere to

sorry!

btw, lighten up :D they are just tyres

i have a garage full of semi's too so hopefully i am not too wicked!

Edited by LSX-438
What is it with you guys and full slicks.

The basic ethos of time attack is built solely around mad lap dashes on SEMI SLICKS.

Its what sets it apart from circuit racing. Am i missing something or are you all going door to door circuit racing ?

you're missing something. plenty of circuit racing categories mandate semi slick tyres as a control tyre. And there is alot of other forms of club level motorsport than just time attack such as sprints, supersprints, hillclimbs etc. Time Attack is really just a johnny-come-lately marketing spin on sprints anyway, but with a whole lot less rules.

I was doing the hillclimb series in Marque Sports which is a slick tyre category. Combine that with the Kumho slicks being on special and hundreds of dollars cheaper than semis, and that was my decision made.

Hey, i wasnt being heavy guys, Just asking the question. It would appear more people actually do door to door racing than I realised.

If I could afford to swap paint I would be in like a rat up a rope but the risks are too high for me. :D

afaik I'm the only one doing door to door racing on here, and we aren't allowed to run slicks (and neither are ipra, saloon cars or any other basic category). I only run slicks for fun when I get them cheap. Irace is the only place I am allowed to race on slicks.

But for super sprints on an s13, don't expect slicks to be quicker.

Duncan is running good second handies on a 1700kg car.

Neil is running good, soft, new slicks on 400kg car.

But your average second hand slick is second hand for a reason. And ex-race tyres are almost always Medium/Hard or Hard. Neither of which is necessarily going to make a 1100kg s13 go faster in a 3 lap session.

Hey Noel,

I was running the same second hand Michelin slicks in the Ruzic Time attack that Duncan and Marek have been using (68/27/18 porsche cup rears).

Was a bit dubious about them (looked fairly chewed out with only 1-1.5mm treadmarker depth and god-only-knows how many heat cycles in them).

anyway they went very well.

The 55.6 sprint lap compares to another R35 (bill's black one) running 58.1 with new Hoosier 19 inch grooved slicks (R6's I think they are called) and about 50awkw less power.

They transform the car and are now allowing me to be competitive in the 'race' class.

Apart from being exciting to drive on they are dirt cheap. RE55's are about 6-8 x the price.

I should add that the first session of the morning (ambient's below 20) was a rollercoaster ride of sliding through corners and fishtailing down the straights! so yes this needs to be kept in mind when using them. once they got up to temp though it was happy days. I think my best laps had them at about 80 degrees celsius up front and 70's on the rears

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
×
×
  • Create New...