Jump to content
SAU Community

Recommended Posts

hey guys i got a r32 and **** me u can hear the std bov a mile a way! I have a hks air filter and all the pressure is blown out throw that as there is nowhere else for it to go! sounds good!@not sure if the previous owner took the plumback bit off?

what would happen if u put a piece of woopy cushion over the end of the bov snout?? Hehehe imagin the noise hehe

The pipe i think your talking about is the one about an inch in diameter going down towards the turbo? Thats the recirculation pipe it goes back into the pipe from your air filter and is plumbed in just before the turbo. If you take this off youll have to modify your pipe from air filter to turbo, either getting stainless piping or patching the stock one.

S

Just get a pod filter and leave the plumb-back in place, the sound will be almost as loud.

what would happen if u put a piece of woopy cushion over the end of the bov snout?? Hehehe imagin the noise hehe

Hehe, i think a kazoo or something would sound pretty funny too.

ok i tried this the other day and yeah the car runs heaps rich. I loved the sound but....the car wouldnt idle properly and stalled most times i came to a stop. HOWEVER if u disconnect the vacuum line going from the inlet manifold to ur BOV and block it off then..... insted of pshhhhht its "FLUTTER". Sounds amazing and the car runs a little richer but not really noticeable

What, the whoopie cushion idea? Or the kazoo idea?  :P

Check the net and you'll see its been done before, theres some movies around, I think it was some sort of Mazda, tried various things, eg baloons, party streamers etc, sounded quite funny. No link sorry, shouldn't be too hard to find...

Btw, my stock R32 GTSt bov is like twice as loud as the my GTS25t one, same filter too, dunno why that is...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
×
×
  • Create New...