Jump to content
SAU Community

Recommended Posts

ok, i suppose i will give it a shot, if it will help with coming on boost earlier.

i was just more concerened about it casuing damage if not done with any other appropriate mods,

as far as i understand it'll have bad effects on the turbo causing early failure............

Link to comment
https://www.sau.com.au/forums/topic/327936-m35-bov/page/4/#findComment-6156734
Share on other sites

The bov still works fine with the grub screw in, all its doing is bypassing air back to the intake so there isnt a huge pressure differential when the bov opens. My car ran fine with it plugged, it also held boost better and this would help the turbo last by bringing shaft speeds down. Why compress all that air then bleed it off if you dont have to, especially if you are trying to hold over 20psi.

Just run a 5mm tap into the 4mm hole and stick a grub screw into it. :thumbsup:

(Wont fix farting noises, that would be either BOV piston seal or manifold to turbo gasket most probably)

Link to comment
https://www.sau.com.au/forums/topic/327936-m35-bov/page/4/#findComment-6157292
Share on other sites

If you had some way of tuning the ecu you could try and take out the fuel dump when the bov opens, I think the Emanage can do that to some extent, otherwise no, the air is metered and needs to remain in the system.

Realistically any car with airflow meters can't run atmo, only map sensored cars can which is why the epa made it illegal.

Link to comment
https://www.sau.com.au/forums/topic/327936-m35-bov/page/4/#findComment-6158865
Share on other sites

I'm running Aaron's Turbosmart Kompact with the stiff spring at the moment, its quite snappy when backing off but feels good none the less. The stock one was working fine with the grub screw mod but it could be due to the tune.

I ran 19psi on the stock turbo for 4 or 5 months, don't do it unless you are prepared to replace the turbo obviously, although I have a spare here. :whistling:

To run high boost on the stock turbo, or any highflow version of it, you will need one of my modified actuators. That should hold around 15psi and allow over 22psi with a controller. Without the stiffer actuator it wont hold more than 14psi in the top end.

Link to comment
https://www.sau.com.au/forums/topic/327936-m35-bov/page/4/#findComment-6159967
Share on other sites

  • 3 months later...

Has anyone actually figured out if this is a BOV problem?

I still have the exact same issue, and Im confident its something to do with the wastegate as you can hear it reverberate right through the exhaust. It literally sounds like its underneath you when driving. If you hold the throttle right when it happens you can make it fart as long as you want. I tried blocking my BOV and still had farts.

To me it sounds like the wastegate isn't opening properly or shuddering. It only farts under medium load. If i floor it it cannot fart - its like it opens properly then, but if im building boost up a hill slowly it happens most of the time....

Surely if it was BOV it would still fart when I floor it. It would fart at the same boost level everytime?

I want to fix this as it shits me!

Benny,

Did you get this sorted, your description is much closer to what my car is doing. Wastegate or BOV?

Chris

Link to comment
https://www.sau.com.au/forums/topic/327936-m35-bov/page/4/#findComment-6295683
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...