Jump to content
SAU Community

Recommended Posts

Not a bad start. I hope you're in one of the states that don't have any p plater restrictions otherwise you will have a tough time getting through your p plates.

WA plates - no restricitons... YET

mate nice 33 just please dont rap it around a pole or try and impress your friends on the street, they already have a bad enough rep.

also how did you find that for 5K ??? whats wrong with it?

Yeah, don't put the BOV on unless you are fitting the stock BOV back on, which you should already have.

ROFL +1

Congrats on the purchase though... looks pretty good for the price - anything wrong with it?

to answer the OP's questions of "What do ya think? Good car for an L plater", for 5 grand i wonder what's wrong with it, and no i don't think it's a good car for an L plater.

and as was said above, just leave the stock bov on there. don't rice ti up with an atmo bov. if you want to hear the stock bov more then put a higher flowing air filter on it.

  • Like 1

your car will have stalling issues if you put a atmo bov on a stock rb25det, don't waste your money and time, just do what mad said and get a high flow panel filter & fmic and you will here the stock plumb back one, and if your after a pod aswell, it is useless unless you fully enclose it, high flow filter is enough flow for now.

  • Like 1
Its an r33 gts-t, picked up for 5 grand cash :)

Stock as a rock, but fitting a BOV and new gasket this weekend.

Probably in the wrong forum, but couldnt find a better one

What do ya think? Good car for an L plater(;

So.. Head gasket??.... "old mate was real honest, it was perfect apart from the headgasket going, and that was only because of the plastic bag that got stuck in the radiator, and nothing else is damaged at all, he was real sad to see it go, he really wanted to fix it, because it is a cheap fix, but his wife just had 10 kids and he has to buy a people mover...."

There is no such thing as a cheap Skyline... Let's pray that with this one clearly having major issues it will not be fast enough to get wrapped around a pole...

nice buy mate, but the wheels, exhaust and wing i noticed in pics arent from factory.

i dont think ive ever seen any skyline go for $5,000, well nothing that has a motor or driveline attached.

you bought privately i assume? i'd get it taken to a mechanic asap to get everything checked out, just to be sure.

oh.. and heed the advice on these forums is my advice :)

Edited by LANDSCRIBBLE
i dont think ive ever seen any skyline go for $5,000, well nothing that has a motor or driveline attached.

I got my 32 for $5k

It ran, but it sure needed some TLC... still needs some now TBH.

congrats to OP on the score. Heed everyone's advice and have her checked out though. Last thing you need is a faulty bilge pump!!

Aha, had a good laugh reading through all the comments(;

The 'gasket' is referring to replacing/repairing the rocker roller cover, which is leaking a few drips of oil. Had a qualified mechanic mate come out with me to have a look at it, just using his terms.

The only other problem would be the rear suspension bushings, which id consider fairly worn. Before I get my license i'll get them replaced.

Also done 172xxxkms, hence reasoning for the price. Besides that mechanically A1 :P

Just picked up a K&N pod filter (from someone on here), which is going in tomorrow.

Theres also a large fmic (from a vl turbo kit) going on in a few weeks. Mate said it should suit fine, anyone with experience care to enlighten?

Dont worry, you wont see this wrapped around a pole on 7 News anytime soon(;

Edited by L-Plater
Aha, had a good laugh reading through all the comments(;

The 'gasket' is referring to replacing/repairing the rocker roller cover, which is leaking a few drips of oil. Had a qualified mechanic mate come out with me to have a look at it, just using his terms.

The only other problem would be the rear suspension bushings, which id consider fairly worn. Before I get my license i'll get them replaced.

Also done 172xxxkms, hence reasoning for the price. Besides that mechanically A1 :D

Just picked up a K&N pod filter (from someone on here), which is going in tomorrow.

Theres also a large fmic (from a vl turbo kit) going on in a few weeks. Mate said it should suit fine, anyone with experience care to enlighten?

Dont worry, you wont see this wrapped around a pole on 7 News anytime soon(;

Gonna need a full hektik stereo and a much bigger wing before you can run with us real racers :P

vindff_575.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...