Jump to content
SAU Community

Am Performance Blast Pipes

Simon-S14

By Simon-S14,
in Group Buys

 Share

Recommended Posts

Simon-S14 Grand Master

Simon-S14

Posted
Posted

Hi Guys

Im running a group buy on AM Performance Blast pipes. they will be twin 4 inch pipes with angled up tips and a straight cut on the end of the pipe. they will have a single 3 or 4 inch entry (depending on your exhaust diameter) and available in muffled or straight thro configuration,

Put simply they look awesome and are high quality items.

Basically once you have the pipes you'd head to your nearest reputable exhaust shop and get them to weld it on and mount it with a couple of hangers... the blast pipes cant be supplied with welded on hangers due to the many different configurations out there.

I will be doing an order of 5 or 10 if i can get enough interest. But it will work like this.

5 orders, straight thro blast pipes $280 each or muffled $310 each

10 orders, straight thro blast pipes $250 each or muffled $280 each.

rrp is around 380 normally.

I will be running this for one month.. or earlier if i can get all the spots filled. but what i will need is payment and addresses of each order and then they will all be sent out. there will be a start and finish date for this buy. Start will be today and finish date will be 26/08/2010 or earlier if all 10 spots are filled. If i only have enough interest for 5 buys then i will go ahead with that and process the order earlier then the finish date.

People Interested

(updated with interest)

now for some pics so you all know what im talking about.

amperformanceblastpipes.jpg

tndsc04083.jpg

tndsc04079.jpg

Link to comment
Share on other sites
siddr20 Grand Master

siddr20

Posted
Posted (edited)

Interested.

Whats the full width of these pipes and the lenght? Gotta make sure it fits thru the gap in my rear bar. Also shouldnt matter if the exhaust is put on the right hand side un like the pic up above on the left.

Edited by siddr20
Link to comment
Share on other sites
  • 4 weeks later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • klutched
      GOT SUM's RB34

      By klutched · Posted

      This morning I carefully reinstalled the manifold and started looking at a couple of things I need to do.  Heat wrap arrived sometime today so I popped into the shed with the missus dishwashing gloves and started wrapping the first half of the dump and the screamer/plumb back.  Once I do the second half I'll be able to final fit the turbo and exhaust up.  Also pulled the harness out today and started terminating it at the ECU end. A connector is done, just need to run the remaining wires that arent in the harness - 12v, gnd and couple I/O
    • Dose Pipe Sutututu
      Rear suspension upgrades

      By Dose Pipe Sutututu · Posted

      A31 is pretty much the same thing without HiAIDS I mean CAS, no improvement lol. Not to late to send it.
    • carnoobb
      Newbies

      By carnoobb · Posted

      Thanks for all the replies! I also wanted to ask if wheels that were fitted on Ford Falcons would fit the 350GTs as well? In the area I'm at there aren't that many options for secondhand wheels and new ones here are way out of my budget. From what I've seen, most of the wheels that are available that were fitted on Ford Falcons have an offset of +33 to +36, with a centre bore of 70.5mm whereas the stock 350GT's ones are 66mm, can't seem to find any hubcentric rings that fit that difference though. 
    • sonicii
      Newbies

      By sonicii · Posted

      215/45/18 tyres are probably a little on the low side compared to the factory tyre, it should be closer to a 245/45/19, which will get you about an extra 11mm of height, and should make you speedo read a bit closer to reality. 245/45/19s will be a bit too far the other way and you risk a speeding ticket as your speedo might read slower than your actual speed.  245/40/19s would be correct if you are going to 19in rims, they will give you a similar total diameter to the 245/45/18 tyres.  
    • GTSBoy
      Rear suspension upgrades

      By GTSBoy · Posted

      That's something I forgot to put in my list. The aggressive anti-squat in R32 is a f**king menace. I still need to decide if I'm going to drag the subframe out of my car and weld in the GKTech corrector kit. The main reason to dither is the need to switch to spherical joints in the lower arm to account for the twist induced in the rear pivot caused by lowering the front pivot. And yes...we do put better subframes in R32s, and I wish I'd gotten an S14 one instead of an A31 when I did the "take off and nuke it from orbit" HICAS delete all those years ago.
×
×
  • Create New...