Jump to content
SAU Community

Recommended Posts

some people are holders of said key :woot:

Manildra (Fueltown) E85 all the way baby! :laugh::)

I will prob use Caltex E85 in the warmer months, but only once Trent has had a check over it on the dyno with the fuel in. Even the variance between United and Fueltown needed a little tweaking.

But i reckon get something installed in the tank to monitor ethanol levels and get an ECU to modify accordingly (interpolate between two+ maps). Basically how the the flex-fuel cars work. Just need a good enough ecu i guess.

  • 1 year later...
  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

How has this all progressed? Lots of loose ends, posting here for Googleability. Can't seem to find much info from the Google.

Where can I find current E85 prices?

How has the price/economy of it changed? (I don't drive currently so I don't know the prices)

Have any people noticed any ups and downs after an extra year of use?

Edited by jukic.j

So it's about 25c cheaper but about 30% more fuel is used unless I muddled that figure?

Don't forget to add 15% more HP into the equation.

Heard a rumour that United is going to equip more servos with E85. Any truth in that or is it simply just a rumour?

Would love to get the 33 on E85 full-time but the lack of nearby servos that stock it worries me lol

More, 50-70c

United E85 - 97c

BP98 - $1.60

$1.60? There do you fill up :O

I paid i think $1.45 the other day, might have been less. ULP on the usual good days has been ~$1.25 so it wasn't too much more.

But i reckon get something installed in the tank to monitor ethanol levels and get an ECU to modify accordingly (interpolate between two+ maps). Basically how the the flex-fuel cars work. Just need a good enough ecu i guess.

hahahahah.... indeed.

Melbourne is quite spoilt for E85 outlets - United has quite a few now, it's a pity the Caltex roll-out seems to have stalled a bit though. Don't really care though, as you're better off running United anyway.

United in Scoresby has E85 that wasn't on the website last time i looked too.

Yeah I think I'm going to run E85 too, well at least look into it seriously. I'm pretty spoilt for choice with stations around me (Caltex and United).

Just not sure how much more efficient it'll be. Still I'm finding that I'm paying around 1.45-1.54 for ULP. Dunno where some

Of you blokes are getting those mint prices! :D

Where are you located? There's heaps of E85 servos around me

The 33 stays in Berwick most of the time but also keep it in Frankston occasionally too.

Only Uniteds I know of that stock around those two areas are Patto Lakes and Hallam :unsure:

The 33 stays in Berwick most of the time but also keep it in Frankston occasionally too.

Only Uniteds I know of that stock around those two areas are Patto Lakes and Hallam :unsure:

Hallan close enough !!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...