Jump to content
SAU Community

Testing If Vct Is Working Properly

Chi100188

By Chi100188,
in Engines & Forced Induction

 Share

Recommended Posts

Chi100188 Mentor

Chi100188

Posted
  • Author
Posted

well last week i was getting car tuned had a few problems in the past such as cas,coil packs, exhaust cam gear set on 2 degrees retard all been fixed now and the car still wouldn't make any power down low until 5k rpm the power would just shoot up so the tuner reckon it was the VCT not work so i changed the solonoid but i want to test if the vct is really work or not

PM-R33 Grand Master

PM-R33

Posted
Posted (edited)

First thing do this:

1. Start car

2. Remove plug from VCT solenoid

3. Set up test light onto VCT solenoid plug

4. Get some one to put car into gear (obviously holding the clutch in) and rev the car

The test light should light up above the 1200ish rpm and stay lit until the 4500ish rpm. This will tell you that the ECU is actually giving power to the solenoid.

The only way now is to put it onto a dyno and do two runs back to back plotted on top of one another. One with the VCT plugged in, one with it unplugged. If both runs are identical you know you have a problem with the solenoid itself. It is pretty rare to have a solenoid fail though.

Edited by PM-R33
Messiah Mentor

Messiah

Posted
Posted

or poor mans seat of the pants approach.

Give it a bootful in low gear to 4k rpm with vct plugged, ensure you stay below the speed limit.

step 2.

Unplug vct and repeat, if run two feels like arse... vct is working ok in run one. if they feel the same... vct is broken

Kaido_RR Grand Master

Kaido_RR

Posted
Posted
what ecu are you using? may have to setup vct as an output.

Its running a PFC.

we have have heaps of issue with the car and has been to the tuners now 3times and still no complete tune, so the owner is getting abit dishearten hence why we want to work out if the VCT is working.

We did a swap yesterday using the old VCT solenoid from my old engine, however we are not 100% sure if the solenoid was the problem or if we needed to swap the cam gear aswell

RRob Community Regular

RRob

Posted
Posted
You should be able to hear the solenoid click when you pull the throttle when under the bonnet, this would suggest it is working... It's a noticeable noise

The car has to be in gear(just not in neutral) for this to work.

Chi100188 Mentor

Chi100188

Posted
  • Author
Posted

so i pretty much sit in the car put it in first clutch in rev it till 4000 rpm to and get another person to have his ear in the engine bay to hear a click or not or alternatively just drive the car with the vct plug in then take it out and see how the drive is after that?

  • 2 weeks later...
Rolls Grand Master

Rolls

Posted
Posted

Where is the VCT solenoid in the engine bay? Also when does it switch on, 1500 - 4000 rpm? or is it 5000 rpm.

Just got my eboost street and it has a window aux function which I am planning on using to control my VCT.

Also does the VCT activate when you ground the relay, or provide power to it?

Cheers

  • 1 year later...
urtwhistle Proficient

urtwhistle

Posted
Posted

Hey guys I'm wondering if I have potential problems with VCT on my R34 also.

I have tried testing it as well as I can until it goes on a dyno, so please give me your thoughts.

I removed the VCT plug and applied power directly to the solenoid and it clicked as it should have. I measured the voltage at the plug @ idle and it had 10v but I couldn't get it to trigger and go any higher.

I tried setting the power fc trigger points at 0 4500 and 7400rpm and 7400 gave the best boost response for some reason.

I also tried driving around with it plugged in and unplugged and there was no difference.

Rolls Grand Master

Rolls

Posted
Posted (edited)

You need to put it on a dyno and wire it on all the time, do a power run, then unplug it and do another dyno run.

Now overlay the two graphs, where the graph with it permanently on dips below the graph with it always off should be your ultimate switch over point. Doing anything other than this is guessing and will give sub optimal results.

53948234.jpg

edit it is possible the solenoid is jammed, I had to hit mine with a hammer and then pulse it on and off 10 times to get it to start clicking.

Edited by Rolls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB25DET Series 1 & Series 2 Gearbox Identification

      By GTSBoy · Posted

      I should. But it already uses too much fuel for a daily. You might note my recco for engine chnages are almost exclusively to people who have it as a weekender/summer car. I don't even have room to keep the spares for this one, let alone another car.
    • MBS206
      RB25DET Series 1 & Series 2 Gearbox Identification

      By MBS206 · Posted

      He should do an LS7 too...
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      If I had "perfect R33 GTR" kinda money I would have bought one of the crazy expensive low mileage HJA cars, but I am sadly not that wealthy. I already picked this car out of various Skylines for sale locally, most of which were worse in some way. Only a few cars were actually better but also more expensive. In terms of buying a motor locally, I at least have the option to inspect it myself and juding the seller as a person, and used or freshly rebuilt engines that some people sell are actually ok price-wise. I knew the car was going to require work, but shit piled up real fast and I haven't even driven 1000km yet as the turbo started oiling like a bitch within a few weeks after I got the car.   I assume it wasn't actually me who cracked it, though there is no way to know when that crack formed and if the previous owner even knew it was there. Buying another 05U Block can be a gamble, yeah, but the cheapest PRP cast block is like twice or more money-wise, and billet is 3 or 3 times as much. For now I am most likely just keeping the current engine, as a rebuild or engine swap isn't happening right now. But I am seriously considering buying a second engine and selling mine in return. Might be a sweet deal at the end.
    • sunsetR33
      RB26 turbo oil banjo bolts

      By sunsetR33 · Posted

      Hi all. I need some help buying the correct size banjo bolts for my 2860 turbos. Because whoever installed them tore up the original part, I ordered new ones of this kind, because I just figured these were the most leak-resistant option as I already had trouble with a shitty braided line. I need to know the thread size of the smaller left hole, that is the turbo oil feed connection. I found out so far that the turbo oil inlet apparently has a 7/16"-24 thread, but I cannot find any listing or description of the thread size on this line. I do not have the original bolts. I tried using the bolts that were in the turbos (the ones that were mounted with the shitty braided line) but they sit very loosely so they can't be the right thread. Means either these bolts are the wrong ones (how do they fit the turbo then? no clue) or the wraparound-lines have a different thread than the turbo oil feed itself. Help is appreciated, asking Nissan directly is obviously not going to work.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      EDIT: PSA to whoever stumbles upon this thread. It is in fact a crack in the block that caused this concern. Just letting you know. In my case, a few cm long hairline crack going horizontally above the turbo oil feed. Classic RB shit I guess
×
×
  • Create New...