Jump to content
SAU Community

Recommended Posts

Hi guys,

i just wanna know is it possible to remove a turbo from a GTT engine, guys if theres a way i'd like to hear it. Cause i've heard of ways like, removing the manifold, and replacing it with another non turbo manifold. Can this be done? Will it affect the engine? Will it even be drivable?

Leave your ideas and stuff below :wacko:

Link to comment
https://www.sau.com.au/forums/topic/334282-r34-gtt/
Share on other sites

Not this shit again... Of fvcking course it can be removed, but why do you want to? If you mention p plates laws, me and the rest of SAU will loose our shit.

If you want a non turbo skyline, BUY A FVCKING NON TURBO SKYLINE!!!

Link to comment
https://www.sau.com.au/forums/topic/334282-r34-gtt/#findComment-5416464
Share on other sites

No you can't take it off.

The turbo is welded to the manifold, and the manifold is welded to the head, and the head, it's welded to the block, and of course, the block is welded to the body.

So, you'll need to just buy a non turbo version Cheeeyaaaamp.

Link to comment
https://www.sau.com.au/forums/topic/334282-r34-gtt/#findComment-5417097
Share on other sites

No you can't take it off.

The turbo is welded to the manifold, and the manifold is welded to the head, and the head, it's welded to the block, and of course, the block is welded to the body.

So, you'll need to just buy a non turbo version Cheeeyaaaamp.

baaaaaaaaaaaaaaaaaaaahahahahahaha, love your work.

to be somewhat helpful to the OP, yes the turbo can be removed, however you would be better of buying a hyundai excel as it will be faster, and i'm not joking. even a commodore with 2 million kms on the clock that is only running on 4 cylinders will be faster than it.

Link to comment
https://www.sau.com.au/forums/topic/334282-r34-gtt/#findComment-5417183
Share on other sites

I swear to christ, SAU should have some "auto-ban" coding for anyone that mentions this shit. How can people be this f**king stupid!

Dude read this thread, than realise that thread there was the 1,000,000th time some one has asked your question.

http://www.skylinesaustralia.com/forums/tu...bo-t333193.html

Link to comment
https://www.sau.com.au/forums/topic/334282-r34-gtt/#findComment-5417196
Share on other sites

god f**king dam . didnt we sticky this shit just last week .

seriously the change the sign up question to something along these lines .

really over this shit .

yes you can take the turbo off but you will have to change the vvti change over piont and convert the hicas to the front wheels

Link to comment
https://www.sau.com.au/forums/topic/334282-r34-gtt/#findComment-5417969
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...