Jump to content
SAU Community

Recommended Posts

I bought the matic-J oil the other day was gonna do it myself today.. from the info i have found dropping the oil out the drain plug will only remove half then i can just top back up the exact amount i removed.

Or should i take it to a mech and get them to flush and fill with full amount??

im only asking coz i found mixed results, some saying not good to flush the system(unwanted pressure..etc) and others saying not good to just drain as your not removing all the old stuff..

I just want to know what others have done.

either way im happy to do myself, or take to mech as i have bought the expensive stuff.... matic-J is like the cost of liquid gold. :ermm::)

thanks

sorry to start new thread.. but the M35 info one is getting massive and without categories gets hard to find stuff..

Link to comment
https://www.sau.com.au/forums/topic/334650-m35-transmission-fluid-change/
Share on other sites

This is for S1 but pretty sure M35 is the same (i.e. the sump will hold a lot less than half). You could do it without dropping the sump. This way you are just using the stock auto's pump (it has been suggested that the pwer flushing system of the auto shops can damage seals but I can't verify that):

Get yourself an auto sump gasket kit and a 20L drum of (ideally) quality synthetic atf. You need 12 to 14L for the auto and you can use the rest for your attessa and power steering. Drain the sump and drop it (easier said then done - you will have to support the box and remove the rear mounting). You will only get betweeen 1 and 2 litres this way. Check that the new internal filter is exactly the same (otherwise the sump won't go back on) and if not either modify the new one to suit or clean the old one and put it back. Put 2L of fresh oil down the dip stick tube.

Then pull a hose off the trans oil cooler and run the engine until you have pumped out 2L into a container. Pour 2L of new oil down the dipstick tube and repeat until you get clean oil coming out. This will take 12 to 14L in total.

I bought the matic-J oil the other day was gonna do it myself today.. from the info i have found dropping the oil out the drain plug will only remove half then i can just top back up the exact amount i removed.

Or should i take it to a mech and get them to flush and fill with full amount??

im only asking coz i found mixed results, some saying not good to flush the system(unwanted pressure..etc) and others saying not good to just drain as your not removing all the old stuff..

I just want to know what others have done.

You should be able to get quite a lot by draining (about 4L or so), unfortunately ours takes over 8L, so you could do it again the following weekend which is effectively just diluting the old oil with fresh stuff or alternatively take it to Nissan for a transmission flush and take the price of the oil off the bill (you will lose $$ though).

hmmm.... while I think about it, would something like the Liquivac work for removing all the transmission oil?

matic-J is like the cost of liquid gold. :D:(

Maybe look at getting some Matic-S from the US? We have yet to receive it in Australia, but it is the 100% synthetic replacement to Matic-J.

sorry to start new thread.. but the M35 info one is getting massive and without categories gets hard to find stuff..

Agreed.....

couldnt agree more with another forum for m35 stuff.

I keep confusing peoples comments about S1's and S2's until i notice either C34 in their list of cars or their avatar of a c34.. and im like meh doesnt apply to my s1!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
×
×
  • Create New...