Jump to content
SAU Community

Michinbury (great Western Hwy)

GTRAAH

By GTRAAH,
in New South Wales

 Share

Recommended Posts

dannyb Contributor

dannyb

Posted
Posted
IS this a fake speed camera? does anyone know for sure as its really old and there arnt even any warning signs around it

Im not 100% sure but i think its a heavy vehicle trip camera to stop truck drivers doing over there max hours for the day without breaks.......

MaTBoY Grand Master

MaTBoY

Posted
Posted

If you're talking about the camera near the M7 bridge it's a truck emission camera they've been trialling. They might use the housings to test other features on cameras but currently it's not a speed camera.

GTR-N1 Grand Master

GTR-N1

Posted
Posted
It is a truck camera moniters compression braking there's also 1 going down the mountain to wollongong....

^^^ Someone said this on talk-back radio too.

Another person stated that he rang up the RTA and said, "can you tell me what that camera is at such 'n such?"

RTA: "Where is it located again?"

John Citizen: "I said it's at such 'n such"

RTA: "I dunno. Are you sure it's a camera?"

John Citizen: "Yes it's a camera and it's at such 'n such"

RTA: "In that case, we'll send out a truck to investigate."

:yes:

oweban Grand Master

oweban

Posted
Posted
No, we pay tax to the thieving Labor Government that has been ruining the state of NSW for the last 15 years, but that's just my opinion. :D

As much as I'm a "Labor" person (to be honest, not so much them, just more "left-wing"), I agree with you there; State Labor is fkt.

Still don't know why they can't put a "u" in their name.

MBS206 Grand Master

MBS206

Posted
Posted
^^^ Someone said this on talk-back radio too.

Another person stated that he rang up the RTA and said, "can you tell me what that camera is at such 'n such?"

RTA: "Where is it located again?"

John Citizen: "I said it's at such 'n such"

RTA: "I dunno. Are you sure it's a camera?"

John Citizen: "Yes it's a camera and it's at such 'n such"

RTA: "In that case, we'll send out a truck to investigate."

:)

RTA didn't erect them.

DECC did, and they're not monitoring truck compression braking, they are monitoring noise levels of both trucks and cars.

GTR-N1 Grand Master

GTR-N1

Posted
Posted
RTA didn't erect them.

DECC did, and they're not monitoring truck compression braking, they are monitoring noise levels of both trucks and cars.

Thanks Matt...

But what's the difference between the Mt Ousley sound level detection equipment (of truck compression) compared to...

the noise monitoring equipment at Minchinbury? I can't distinguish. :D

MBS206 Grand Master

MBS206

Posted
Posted
Thanks Matt...

But what's the difference between the Mt Ousley sound level detection equipment (of truck compression) compared to...

the noise monitoring equipment at Minchinbury? I can't distinguish. :D

There won't be any.

The problem the DECC have with trucks is that whilst stationary, they may pass their noise emmisions, but when rolling, they become alot noiser. It's not just about compression braking, there's road noise, engine noise, they pick up the trucks quite easily who have leaking exhausts a LOT easier then employing 4 guys to wave every truck in and go over it at an inspection station.

Owen, you can't hear much of the trucks on the other sides of those walls. You'd be VERY surprised how good they are at taking out noise. If there's a worry about compression braking annoying neighbours, they put up signs stating "Please limit compression braking"

When coming down the Mt Ousley, the trucks aren't on compression brakes the whole way, that's why they're limited to low gear. When you come down there in a truck, you actually use the throttle coming down it. Until you drive a truck down there, it's hard to understand...

And Terry, there won't be a difference at all, they're both picking up noisy vehicles, as stated, it's not JUST for compression braking.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • Kinkstaah
      new 1.5 LSD issues/concerns

      By Kinkstaah · Posted

      What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...