Jump to content
SAU Community

Limped My M35 Home

Dunc

By Dunc,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Dunc Mentor

Dunc

Posted
Posted

So basically I was going from a 60 to a 100 zone, car started reving up and making boost and the engine cut out, died completely.

Fortunately there wasnt much in the way of traffic and I had a mates following me in another car (we were going to go camping). The car struggled to turn over, but got there after a couple of attempts but sounded a bit spluttery and the engine light was on. Managed to limp it back home, but I it wont rev much past 2000 rpm, if I tried it would bounce the revs back and forth over a 100-200rpm range and surge almost like a bunny hop. We pulled in to a servo part way back, my mate was low on fuel. I didnt need to fill up but when I went to restart it it REALLY struggled to get going again, almost thought it wouldnt start up at all.

Ive tried to pull the ECU codes, got four zeros. Took the front end off to check the intercooler piping, and also checked the engine bay - all looks to be fine (Im not a mechanic by any stretch though)

Anyone got any thoughts or suggestions as to what I can do/check to isolate the problem?

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/338999-limped-my-m35-home/
Share on other sites
Dunc Mentor

Dunc

Posted
  • Author
Posted
Airflow meter?

That thought crossed my mind too, but surely thatd through an ECU code? http://www.skylinesaustralia.com/forums/Ob...st-t281894.html indicates there are AFM malfunction codes.

Hope you get it sorted quickly.

Cheers mate

Dunc Mentor

Dunc

Posted
  • Author
Posted
Sounds like airflow meter Dunc, at least they have been sourced cheap now, around $80 or so new I think. I have no idea why the codes didnt come up...

Can you borrow somebody's to try?

Its possible to check an AFM with a multimeter, isnt it? Maybe I should give that a go

I take it there arent any AFMs that would work other than a unit off another M35?

scotty nm35 Grand Master

scotty nm35

Posted
Posted
Its possible to check an AFM with a multimeter, isnt it? Maybe I should give that a go

I take it there arent any AFMs that would work other than a unit off another M35?

Quite a few cars use the same airflow sensor but in a different housing, Subaru use it, and many VQ's like maxima.

garetb16 Collaborator

garetb16

Posted
Posted

i let scotty operate on mine too - and they arent repairable as per the older ones.

so will be a new/second hand one

they are available on yahoo auctions japan.

and before you try a 350Z one wont work as the adaptors are different.

unsure about the skyline v35 350gt but id imagine they are the same as the 350Z

Dunc Mentor

Dunc

Posted
  • Author
Posted
mine did the exact thing about 4 months ago.

i was overtaking a car and was in boost when it died mid flight!!!

it was the air flow meter.

I remembered bits and pieces of your thread - couldnt remember the outcome or exactly what was the go. Its reassuring to hear that someone had the same problem and the fix wasnt too costly.

Time to get in contact with Jesse Streeter I guess, doubtful I'll be able to source one here for cheaper than what I can do on Yahoo auctions!

scotty nm35 Grand Master

scotty nm35

Posted
Posted
I remembered bits and pieces of your thread - couldnt remember the outcome or exactly what was the go. Its reassuring to hear that someone had the same problem and the fix wasnt too costly.

Time to get in contact with Jesse Streeter I guess, doubtful I'll be able to source one here for cheaper than what I can do on Yahoo auctions!

They are available here, im sure Jetwreck got onto a cheap source...

iamhe77 Grand Master

iamhe77

Posted
Posted (edited)
Airflow meter? Hope you get it sorted quickly.

+1 and +1

AFM Nissan part number is 22680-6N211

It should be the same as used in the 2001-2007 X-trail and the 2000-2005 Pulsar

Or you could pick one up on Yahoo... they are routinely on there for under $30 (ex shipping & commission)

Edited by iamhe77
  • 2 weeks later...
PetroDola Proficient

PetroDola

Posted
Posted (edited)
Quite a few cars use the same airflow sensor but in a different housing, Subaru use it, and many VQ's like maxima.

you serious ?

doubt my 98rexy spare afm would suit surely ?

Edited by PetroDola
alu-siv_stagea Community Regular

alu-siv_stagea

Posted
Posted

mate i had the same issues about two weeks ago, i only just managed to get my car home, i took out the air flow meter and sprayed it with contact cleaner and it worked an absolute charm, the car hasn't gone better, it's always worth a shot.

macdog Veteran

macdog

Posted
Posted
So basically I was going from a 60 to a 100 zone, car started reving up and making boost and the engine cut out, died completely.

Fortunately there wasnt much in the way of traffic and I had a mates following me in another car (we were going to go camping). The car struggled to turn over, but got there after a couple of attempts but sounded a bit spluttery and the engine light was on. Managed to limp it back home, but I it wont rev much past 2000 rpm, if I tried it would bounce the revs back and forth over a 100-200rpm range and surge almost like a bunny hop. We pulled in to a servo part way back, my mate was low on fuel. I didnt need to fill up but when I went to restart it it REALLY struggled to get going again, almost thought it wouldnt start up at all.

Ive tried to pull the ECU codes, got four zeros. Took the front end off to check the intercooler piping, and also checked the engine bay - all looks to be fine (Im not a mechanic by any stretch though)

Anyone got any thoughts or suggestions as to what I can do/check to isolate the problem?

Cheers!

Have you run over anything? like a rock that could possibly squash your fuel lines?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      Impossible to remove the housing while turbo is installed on the manifold on the engine. So I have to do it anyways. I plugged it so there will not be any debris in there. Will vacuum aswell 
    • JC71
      gtr hood match gt/gtt front fenders?

      By JC71 · Posted

      would a r34 gtr hood line up with gt/gtt stock fenders? after latch, front bumper and hinges are swapped for gtr ones? or would the fenders be too low or high in relation to the hood surface? ( I believe seeing somewhere that gtr front fenders use some type of riser for the sides, but do not know how that relates to stock gt/gtt fenders.)    
    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
×
×
  • Create New...