Jump to content
SAU Community

Recommended Posts

Hi all,

Just wondering what everyone thinks the best first performance mod is for a R33 GT-R?

I know with my XT Forester the single best mod performance wise was swapping the stock exhaust system for a 3" TBE.

Would you say the same for the R33 GT-R?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/343240-r33-gt-r-best-first-mod-option/
Share on other sites

remove boost restrictor,good air filter, whole exhuast with good metal cat, cam gears, boost controller max 18psi on stock comp and injectors, then comp and z32 afms, then injectors and fuel pump, turbos, cams and full engine build, i've done or in process of doing in this order

Thanks guys, much appreciated.

Some of those will have to wait until the bank account recovers from buying the car! LOL

Just curious, will I notice much of a difference if I remove the boost restrictor now?

Also how safe is this given the ceramic stock turbo wheels? And do I need a boost gauge (other than the stock one) and a manual boost controller?

from memory (tuned one awhile back and was not to far off one with 3" cat back) the std 33 GTR exhaust was not too bad at the power levels these make (JDM cats are good, compliance cats are not) boost restrictor removal and tune if your not into more noise from the rear.

Removing the bung improves your air intake... I dont know how is that bad. Plus you can hear the induction and bov sound more and its legal!

But anyway, like everyone else said. Get someone good to look after your car if you're not very mechanically minded. Probably good to get the exhaust system done first (front pipe, cat and catback) and ecu + boost (around 12-14psi should be fine on stock turbo). Read more on the force induction section and you'll find most of your questions already answered.

totally depends on budget

ensure your brakes are up to scratch first, & an oil change & spark plugs

ensure the HICAS fluid is also correct.

next i would

(assuming all is stock)

replace the factory intake - replace with ARC if budget allows or Apexi.

replace factory exhaust / muffler withi something like HKS Hi silent if your wanting a quiet muffler or blitz nur if not

take out the cat , and replace with decat

boost controller run at 1bar.

then dyno run to ensure all is well

fuel pump woudl also be on my agenda

It seems when I am reffering to the boost restrictor others are talking about something to do with the airbox etc.

I am talking about the boost restrictor that is in one of the vaccuum hoses and is marked by the yellow line. It restricts boost to 9psi from the factory and when removed raises the boost to 14psi.

Where is the HICAS fluid located? The manual that came with the car is pretty crap, looks like omething that did not come from the factory.

Where is the HICAS fluid located? The manual that came with the car is pretty crap, looks like omething that did not come from the factory.

There is no HICAS fluid on a R33 or R34 the HICAS rack is electric not hydraulic. And do not waste your money on replacing intake pipes... get everything fixed and ensure everything functions correctly. That will cost you enough before you start spending it on handling better and going faster!

Hi all,

Just wondering what everyone thinks the best first performance mod is for a R33 GT-R?

I know with my XT Forester the single best mod performance wise was swapping the stock exhaust system for a 3" TBE.

Would you say the same for the R33 GT-R?

Cheers.

dont do it, its a slippery slope :blink:

i would personally get everything checked over, stick it on a dyno and check afr, compression if not already checked, service and replace anything thats worn like pads, rotors, tyres etc, after all that, you have a good base to start doing lil mods, i wouldnt take the restrictor out if u running stock turbos, its still a nice car, enjoy it and do the easiest and cheapest mods first so your wallet doesnt have a heart attack

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...