Jump to content
SAU Community

Recommended Posts

5/10

If you're not a stupid little school kiddy, then yes CRD are a reputable workshop. Do some research like searching these forums for keywords, and head to their website.

Also, 1000 horsepower will be setting you back anything around $50,000 and upwards, so enjoy.

Link to comment
https://www.sau.com.au/forums/topic/347878-gtr-upgrade/#findComment-5596116
Share on other sites

hi , im new here

looking for a shop to grade up my gtr

how about CRD , are they good ?

what do i need to get a 1000 horses ?

can somebody help me ?

I suppose it depends which state you live in. For a 1000 horses it would cost alot of money $50-100 grand. My friend who used to have a 33GTR was running a safe tune of 550 hp, however this was only possible after spending about $20 -30 grand on the engine (Stroker kit, HKS cams, dry sump, and the list goes on and on). I believe each state forum has a thread on reputable workshops.

Link to comment
https://www.sau.com.au/forums/topic/347878-gtr-upgrade/#findComment-5596127
Share on other sites

talking alot about where im from

i know someguy here that send his car to CRD

but hes giving me no info

but i heard it went there

i would like to build my car also

what do u need to run a 8-9 sec 1/4 mile

mine is fully stock

has nothing on it

but would like to beat this guy here

he will be the fastest when his car returns

and he had at78 turbo and checked on the internet and gives a max

of 600-700 hp

so i want to be better than that

help please , or should i deal with the japanese

Lots of sugar cane fuel over that way so he should be set. :whistling:

Link to comment
https://www.sau.com.au/forums/topic/347878-gtr-upgrade/#findComment-5598209
Share on other sites

talking alot about where im from

i know someguy here that send his car to CRD

but hes giving me no info

but i heard it went there

i would like to build my car also

what do u need to run a 8-9 sec 1/4 mile

mine is fully stock

has nothing on it

but would like to beat this guy here

he will be the fastest when his car returns

and he had at78 turbo and checked on the internet and gives a max

of 600-700 hp

so i want to be better than that

help please , or should i deal with the japanese

see my earlier response, what is your budget.

Link to comment
https://www.sau.com.au/forums/topic/347878-gtr-upgrade/#findComment-5598215
Share on other sites

about 50,000 dollars plus airfreight to Paramaribo, Suriname

Lol

talking alot about where im from

i know someguy here that send his car to CRD

but hes giving me no info

but i heard it went there

i would like to build my car also

what do u need to run a 8-9 sec 1/4 mile

mine is fully stock

has nothing on it

but would like to beat this guy here

he will be the fastest when his car returns

and he had at78 turbo and checked on the internet and gives a max

of 600-700 hp

so i want to be better than that

help please , or should i deal with the japanese

Wouldn't happen to be an orange/red R33 that was in Zoom?

Link to comment
https://www.sau.com.au/forums/topic/347878-gtr-upgrade/#findComment-5600966
Share on other sites

well these days $50K USD is roughly equal to $50K AUD so you should get close. your best bet is talk to CRD and ask them what they think of the project. do you plan to send them the whole car or just want an engine built etc?

Link to comment
https://www.sau.com.au/forums/topic/347878-gtr-upgrade/#findComment-5601255
Share on other sites

is that the only shop and throzzle waht do u mean with me being able to make that money here ?

well these days $50K USD is roughly equal to $50K AUD so you should get close. your best bet is talk to CRD and ask them what they think of the project. do you plan to send them the whole car or just want an engine built etc?

Link to comment
https://www.sau.com.au/forums/topic/347878-gtr-upgrade/#findComment-5601770
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...