Jump to content
SAU Community

Recommended Posts

Hey Guyz, i am planning on picking up an Walbro fuel pump for my car and just wanted to know which is the one i should buy for my car which is bolt on and fits fine to an R34 GTT, i am a bit confused between the GSS 341 and the GSS 342??

Thanks Guyz!!

Link to comment
https://www.sau.com.au/forums/topic/348153-walbro-gss-341-or-342/
Share on other sites

I'd only Get a Nismo/Tomei on an S14/S15/R33/R34. The Warlbro sock is on a 90 degree andgle but it needs to be 45. Same prob with a Bosch 040. Mounts on a 45 degree angle so won't pick up low fuel levels well at all.

I HATE spending money I don't have to but I do strongly think it's necessary unless U wanna only use 3/4 of your fuel tank.

Isn't the difference between 341 and 342 whether the inlet is on the right or left side?

As far as running out of petrol? I've never had an issue with my walbro (342). I installed it myself on a empty tank that the needle was at the line (not on the line - level with the empty line) - no issue from very first prime! I've been below the line several times. Filled with 55L and still didn't have problems.

who is dumb enough to "GIVE" it some on a windy hilly road with it dead on empty? cmon be realistic here.. also im the same as simpletool, installed walbro pump and i have no dramas running it right down near the empty line

Ok so from the above posts im gathering that both the GSS 341 and the GSS 342 will fit, any differences in fitting or using them?

Im not buying it from Australia thats why i want to know exact details before i buy it... So the 341 or 342??

A walbro is perfect for an S13 or R32 because the bracket is vertical. S14/R33 and later go on a 45 degree angle riiiiight down in there, causing the sock to angle 45 degrees upward. I guess u could work something out to make the sock sit a bit flatter.

Edited by bradsm87

I'd only Get a Nismo/Tomei on an S14/S15/R33/R34. The Warlbro sock is on a 90 degree andgle but it needs to be 45. Same prob with a Bosch 040. Mounts on a 45 degree angle so won't pick up low fuel levels well at all.

I HATE spending money I don't have to but I do strongly think it's necessary unless U wanna only use 3/4 of your fuel tank.

Yeah this, I got a 342 in my rb20det hr31 and any less than 1/4 a tank if you booted it around a corner it would fuel starve, not an issue with a stock pump or other pumps, you can probably modify the sock but it was a massive pain in the ass for me.

Edited by Rolls

A walbro is perfect for an S13 or R32 because the bracket is vertical. S14/R33 and later go on a 45 degree angle riiiiight down in there, causing the sock to angle 45 degrees upward. I guess u could work something out to make the sock sit a bit flatter.

My R33 has a vertical bracket.

Ok so from the above posts im gathering that both the GSS 341 and the GSS 342 will fit, any differences in fitting or using them?

Im not buying it from Australia thats why i want to know exact details before i buy it... So the 341 or 342??

Like I said 341. if you specify the vehicle you can get the most appropriate fitting kit.

you know the r33 sock of the stock fuel pump fits directly onto the walbro.

I've had a walbro in two of my 33's and an s14, each time I've used the factory sock as it's longer and sits at the right angle.

Just some food for though ;)

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • TBH, it sounds like the threads on the bolt are fubar in a specific section. Most likely as you've been working it back and forth it has torn threads out, as you loosen the bolt, this section enters the nut, now you're spinning a round shaft inside the nut, there's no threads here.   Use something similar to a claw on a hammer that will fit either side of the bolt head and try to apply downward force while also undoing it. The idea is to attempt to catch a thread, or just rip the f**ker out. Caution on ripping out, as it could bend/maime/mangle what the captive nut attaches to. If the captive nut is actually okay, you could do the dirty part of cutting the head off the bolt, then cut a slit in the end of the thread that's now exposed and then screw it up and into the area the captive nut is until it falls out the other side. However, this does risk the remainder of the bolt rusting over time and damaging near the captive nut and also making it rust. However, so can cutting pieces of panel work out to access this area if you don't reseal it properly.
    • Well, every piece of information on that part when you track it back to Nitto says it's for a KIT of theirs. It is also designed thicker to be stronger. And they speak about a specific harmonic balancer bolt they supply for the whole setup.
    • Techniques for removing stuck bolts are: hitting the bolt head with a hammer, heating the bolt to red hot then letting it cool and working it back and forth like you are already doing. AFAIK the idea is to try to crush whatever material is stuck between the threads (and heat also melts locktite but that's almost certainly not relevant in this case).
    • Yuh, I think it works with the Nitto gear only. I presume that you're not also using the Nitto gear? Watch the video. Compare the interface between the Nitto gear and washer (on the gear side) vs the stocker and decide if you think the Nitto gear is different from stock there.
    • Liking the new charger, battery all good (I think).   Also like how you can put it in power supply mode too. Will troubleshoot with that sometime soon.
×
×
  • Create New...