Jump to content
SAU Community

Recommended Posts

Hey Guyz, i am planning on picking up an Walbro fuel pump for my car and just wanted to know which is the one i should buy for my car which is bolt on and fits fine to an R34 GTT, i am a bit confused between the GSS 341 and the GSS 342??

Thanks Guyz!!

Link to comment
https://www.sau.com.au/forums/topic/348153-walbro-gss-341-or-342/
Share on other sites

I'd only Get a Nismo/Tomei on an S14/S15/R33/R34. The Warlbro sock is on a 90 degree andgle but it needs to be 45. Same prob with a Bosch 040. Mounts on a 45 degree angle so won't pick up low fuel levels well at all.

I HATE spending money I don't have to but I do strongly think it's necessary unless U wanna only use 3/4 of your fuel tank.

Isn't the difference between 341 and 342 whether the inlet is on the right or left side?

As far as running out of petrol? I've never had an issue with my walbro (342). I installed it myself on a empty tank that the needle was at the line (not on the line - level with the empty line) - no issue from very first prime! I've been below the line several times. Filled with 55L and still didn't have problems.

who is dumb enough to "GIVE" it some on a windy hilly road with it dead on empty? cmon be realistic here.. also im the same as simpletool, installed walbro pump and i have no dramas running it right down near the empty line

Ok so from the above posts im gathering that both the GSS 341 and the GSS 342 will fit, any differences in fitting or using them?

Im not buying it from Australia thats why i want to know exact details before i buy it... So the 341 or 342??

A walbro is perfect for an S13 or R32 because the bracket is vertical. S14/R33 and later go on a 45 degree angle riiiiight down in there, causing the sock to angle 45 degrees upward. I guess u could work something out to make the sock sit a bit flatter.

Edited by bradsm87

I'd only Get a Nismo/Tomei on an S14/S15/R33/R34. The Warlbro sock is on a 90 degree andgle but it needs to be 45. Same prob with a Bosch 040. Mounts on a 45 degree angle so won't pick up low fuel levels well at all.

I HATE spending money I don't have to but I do strongly think it's necessary unless U wanna only use 3/4 of your fuel tank.

Yeah this, I got a 342 in my rb20det hr31 and any less than 1/4 a tank if you booted it around a corner it would fuel starve, not an issue with a stock pump or other pumps, you can probably modify the sock but it was a massive pain in the ass for me.

Edited by Rolls

A walbro is perfect for an S13 or R32 because the bracket is vertical. S14/R33 and later go on a 45 degree angle riiiiight down in there, causing the sock to angle 45 degrees upward. I guess u could work something out to make the sock sit a bit flatter.

My R33 has a vertical bracket.

Ok so from the above posts im gathering that both the GSS 341 and the GSS 342 will fit, any differences in fitting or using them?

Im not buying it from Australia thats why i want to know exact details before i buy it... So the 341 or 342??

Like I said 341. if you specify the vehicle you can get the most appropriate fitting kit.

you know the r33 sock of the stock fuel pump fits directly onto the walbro.

I've had a walbro in two of my 33's and an s14, each time I've used the factory sock as it's longer and sits at the right angle.

Just some food for though ;)

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
    • Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
    • Should replace OR drop the tank, give it's good clean. Might be worth replacing that entire fuel level/pump/cradle thing with this: https://frenchysperformancegarage.com/products/fpg-s13-180sx-r32gtst-single-pump-hanger-kit-billet-hat-6-v3-fpg-089?gQT=2  
    • Thank you so much for the help
×
×
  • Create New...