Jump to content
SAU Community

Recommended Posts

Yeah agree, but it was just timing, nothing complex! Thats my excuse and I'm sticking to it!

Off to buy an Emanage then... any suggestions where?

Is there anyone in SA who can tune an Emanage?

The place where I got it from (ebay store) was located in Japan, I'm pretty sure I got the EMU + harness for around $600/650 delivered.

Unfortunately they were affected by the Tsunami and they don't seem to sell EMU's anymore...

Love ebay sometimes.

Emanage Ultimate: http://cgi.ebay.com....e=STRK:MEWAX:IT

Universal Harness: http://cgi.ebay.com....=item588275acd9

MAP Sensor: http://cgi.ebay.com....=item27b7e1a13d

(Did see this cheaper sensor, but looks dodgy as! http://cgi.ebay.com....=item230fca0ec0)

Think thats it for an Emanage install?

Oh, and Informeter: http://cgi.ebay.com....e=STRK:MEWAX:IT

Sounds like it might be a useful acquisition?

dont get the dodgy ones. if they arent an accurate reading, your fuel map can go right out..

Informeters a good doo hicky..although its not really important. you can get another boost sensor and wideband into it. it will tell you your water/intake temp.. throttle % speed RPm.. but the injector duty sycle n some other stuff will be incorrect as a tune will change figures.

The place where I got it from (ebay store) was located in Japan, I'm pretty sure I got the EMU + harness for around $600/650 delivered.

Unfortunately they were affected by the Tsunami and they don't seem to sell EMU's anymore...

they only had two ECU'I bought one, then you bought one.. i tried messaging him about the profec B, but paypal sent me money back. i think his shop was destroyed in the tsunami. poor guy!

map sensor is needed the way i see it. its the safest way as your Tuner isn't simply guessing. hes calculating figures!

when you look for injectors, ask for the plugs. you will need to cut the stock connectors off and solder the new ones on. I'm using Seimens Deka 610CC and im about 80% duty with e85. work fine and dont miss a beat. they are a 4 squirter!

A wide band will help for road tuning, but the dyno should have one for the dyno....i guess if you want one..

i pulled my turbo out again, to open the wastegate up.

took me 2 n abit hours.. proud much??

opened up the wastegate. put everything back together. and no change. what a waste of a day.. looks like the actuator may be playing up :(

woe is me.sad.gif

i pulled my turbo out again, to open the wastegate up.

took me 2 n abit hours.. proud much??

opened up the wastegate. put everything back together. and no change. what a waste of a day.. looks like the actuator may be playing up :(

woe is me.sad.gif

What was the car doing that made you think something was going on with the wastegate?

I ordered an Informeter. That way I don't have to guess whats going on and worry unnecessarily.

Probably do FMIC next. Still deciding whether to do fuel system before emanage or vice versa. Coming along nicely! :thumbsup:

You'll have to come by and do mine soon Aaron :P

lol i told scott that you needed this done.. he laughed hahah

What was the car doing that made you think something was going on with the wastegate?

I ordered an Informeter. That way I don't have to guess whats going on and worry unnecessarily.

Probably do FMIC next. Still deciding whether to do fuel system before emanage or vice versa. Coming along nicely! :thumbsup:

its over boosting. would hold 15psi through to about 4500rpm and then shoot up to 22psi. felt as if the Wastegate was too small and as the exhaust air flow increases it cant push any more through the gate and comes out the fan again, only to continue boosting. I opened up the wastegate as much as i could. and no change.. looks like the actuator isnt allowing the gate to open enough...

lol if anything the informeter will make you worry more when you start seeing figures.. trust me, its why Craig got rid of his lol

Got it back from panel and paint... All new again.. Insurance company sent me a brand new wheel instead of repairing old one and bruce from mag and turbo gave me a tire to use till I save up for a new set! LEgend!

So today I pick up and fitted a black bonnet, was easy enough to change over just not to sure if its what I want anymore. Maybe after a few weeks I'll decide if I'm gonna keep it on or change it back.

What you think?

With:post-78650-0-26587500-1304759786_thumb.jpg

Without:post-78650-0-60149100-1304759710_thumb.jpg

yeah was thinking roof, mirrors and the little bit behind the rear side windows need more black.

Then maybe I'll change the chrome stripping to black, then black out the headlights and foggies, tint the rear lights hmmm where to stop?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...