Jump to content
SAU Community

Recommended Posts

Just got outbid on Mines ECU on YAJ only 5 minutes ago...Got me in the dying seconds.... >_<

post-12229-0-52720000-1314015986_thumb.jpg

Oh well.....

really?

i thought if you bid within the last 5 mins on YAJ it extended it another 5 mins?

Its possible the IM interface timing isnt spot on......

anyway, sucks that you missed out on it, would have been a nice toy!

really?

i thought if you bid within the last 5 mins on YAJ it extended it another 5 mins?

Its possible the IM interface timing isnt spot on......

anyway, sucks that you missed out on it, would have been a nice toy!

Yes, but it is 10mins, not 5.

Well that's what has always happened to me :(

No ebay sniping on Yahoo Auctions

Finally did the "wire" mod today.

I shouldn't work on cars after night shift; everything seems to take twice as long...

Edited by Daleo

Finally did the "wire" mod today.

I shouldn't work on cars after night shift; everything seems to take twice as long...

Tired, eyes a bit blurry & cutting wires at the ECU. Yep, recipe for success, lol.

Tired, eyes a bit blurry & cutting wires at the ECU. Yep, recipe for success, lol.

Lol, yeah, I might've checked everything a few (hundred) times before cutting; just to make sure.:thumbsup:

Car starts, and no fault lights.:banana: Going to wait 'till later for a test.

Mind started ticking away; had to go for a drive...:banana:

That's a surprisingly useful little mod!

Wired up a switch to reset if need be. Is it just a case of close circuit, tap brakes, fault gone?

Good work for doing the hard yards guys; riding your coat tails is a great thing.:thumbsup:

What was the "wire" mod again?

Ecu harness, Pink wire, blue trace; cut, insert momentary switch, have access to full throttle opening whenever you like.:thumbsup: Enjoy better low speed throttle response and no delay after brake application.

Every now & then, close circuit and tap brake to avoid ECU going into "Limp Mode"

Anyone else care to fill in any holes in my explanation?

And I edited your post for the (future)emanage people

Ecu harness, Pink wire, blue trace; cut, insert momentary switch, have access to full throttle opening whenever you like.:thumbsup: Enjoy better low speed throttle response and no delay after brake application.

once you notice something shifty going on afeter approx 100km, go for another emanage tune. much better than just resetting.

Is there any way to send a constant signal to the ecu on that wire so it thinks it's connected and won't need to be reset all the time?

Could you hook the brake pedal light switch to that ECU wire to give a signal everytime the brakes are used? I don't know what voltage it see's/needs, just thinking of ideas.

Edited by slippylotion

really?i thought if you bid within the last 5 mins on YAJ it extended it another 5 mins?Its possible the IM interface timing isnt spot on......anyway, sucks that you missed out on it, would have been a nice toy!

I don't use IM. I have a mate in Japan who was on it for me to 49,000Y (much cheaper for me this way - avoid IM's commission). I was trying to call him for the last half hour as i was watching the bidding get higher and higher to up the bid a bit, however couldn't get him on phone....I was stuck! You are right in that time is extended with YAJ - i just couldn't get a subsequent increase in bid on.....

I recently bought the ex Andy, then ex Aaron Impul ECU which i have here, and was only going to get this one to compare!

What were the specs that the comp runs with?

No idea?? That's why i was interested in comparing differences between this and the Impul...

What were the specs that the comp runs with?

No idea?? That's why i was interested in comparing differences between this and the Impul...

Mine's generic tune (from memory)

RPM limit raised to 7100 or 7300 (can't remember which)

Boost raised to 1.1bar

Speed limiter removed

Throttle remap

Fuel/timing remap

Of course, the end user could specify whatever the hell they wanted (2bar boost and 7,500rom for instance) and all Mine's state is "yes, but please consider the risk"

Take your word for that info Cam. There wasn't a great deal of info on the listing. Is that info straight from mines?

You probably already know but I left the wiring diagram books with Aaron for you to collect and borrow.

Is there any way to send a constant signal to the ecu on that wire so it thinks it's connected and won't need to be reset all the time?

Could you hook the brake pedal light switch to that ECU wire to give a signal everytime the brakes are used? I don't know what voltage it see's/needs, just thinking of ideas.

i doubt it, if it detects connection while the brake is applied theres not point in having it.its best and easiest to have a momentary switch

i suggested a timer circuit, or something hooked up to the water temp. so it gets brake signal till the engine gets to 70degrees. before then you arent going to need to hammer it

i suggested a timer circuit, or something hooked up to the water temp. so it gets brake signal till the engine gets to 70degrees. before then you arent going to need to hammer it

but who would go through the trouble of that? lol if commsman doesnt, i dont think anyone will.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...