Jump to content
SAU Community

Recommended Posts

Hows your $600 spring work Jethro?

Brrrrrppp! Lucky your shifts arn't too good anyway Jethro as you car might finish breaking in half!

Lets just say they work better then your dick does, by the sound of things....:whistling::nyaanyaa:

Edited by ironpaw

Hows your $600 spring work Jethro?

Brrrrrppp! Lucky your shifts arn't too good anyway Jethro as you car might finish breaking in half!

hahahahahahahahahahahahahahahaha f**k

Did the wire cut mod. It certainly builds up the revs a lot quicker while braking now but I can't say I noticed a huge difference. I do have some big wheels on though and no (or insignificant) power mods though...

Did the wire cut mod. It certainly builds up the revs a lot quicker while braking now but I can't say I noticed a huge difference. I do have some big wheels on though and no (or insignificant) power mods though...

You can't receive new messages...

Remind me what size did you go for with the wheels? They were 19x something right?

Have any problems with fitment?

You can't receive new messages...

Remind me what size did you go for with the wheels? They were 19x something right?

Have any problems with fitment?

Saw them tonight. Great fitment.

From memory they are 19x9.5 +20, quite a bit of low and some slight guard rolling was done too I believe - Jase can correct me if Im wrong :P

Did the wire cut mod. It certainly builds up the revs a lot quicker while braking now but I can't say I noticed a huge difference. I do have some big wheels on though and no (or insignificant) power mods though...

TBH its still a slug off the line. from standstill to 30ish kph the response sucks....unless you've got nismo ECU and/or revving the engine with the brakes on...

The rental Tiida my wife is driving (her car's in the shop again) seems to go harder then my Stag from standstill...

of course, I'm redlining the damn thing and I look at the speedo and its barely reaching 60 kph...LOL

Edited by ironpaw

Saw them tonight. Great fitment.

From memory they are 19x9.5 +20, quite a bit of low and some slight guard rolling was done too I believe - Jase can correct me if Im wrong :P

Yep as above.

Ultimately it just comes down to what height you want to run your car at. Chris aka spoolin12 runs the exact same wheel size (maybe a +22 instead of a +20, can't remember), with the same tyre (245/40 R19) and runs his car a bit higher. The rear wheels are flush (the rears were never really a concern, only fronts), and the fronts hang just slightly out of the guards.

Mine is that bit lower (still pretty high, I never bottom out except for on big spoon drains when any other car would, or during a hasty exit from the RAAF base the other day >_< ) so it's running that bit more camber. Front and rear they sit absolutely perfect. :thumbsup:

We rolled all four corners on my car - all it needs is the lip folded up. Now that mine is a bit lower now I don't even think that the rears needed any folding. Fairly confident I've never rubbed a guard, and IF I did it was under a fair amount of compression as I hit a dip in the road coming down one of the hills on Tregarthen Rd. Couldn't see any rubber missing from the tyre or left on the guard, so I'm not particularly concerned.

Long story short, they will fit, and look HOT. How well they fit comes down to heights. If you're going to run it higher (similar to Dale's heights in the BC BR thread, I'd probably go for a 19x9+20 or a 19x9.5+30). Really just comes down to preferences. PM me if you want to check them out one night.

TBH its still a slug off the line. from standstill to 30ish kph the response sucks....unless you've got nismo ECU and/or revving the engine with the brakes on...

The rental Tiida my wife is driving (her car's in the shop again) seems to go harder then my Stag from standstill...

of course, I'm redlining the damn thing and I look at the speedo and its barely reaching 60 kph...LOL

hahah yep. It's a weight thing. Doesn't help that the last car I owned was an Evo with a 5 puck clutch haha.

I like the look I yours, just curious about your camber to fit them flush with guards thats all. Mine is about 10mm higher than yours and is running -2.5deg front and -2deg rear. And already seeing inner tyre wear with the limited km's I've done.

I like the look I yours, just curious about your camber to fit them flush with guards thats all. Mine is about 10mm higher than yours and is running -2.5deg front and -2deg rear. And already seeing inner tyre wear with the limited km's I've done.

Whaaaat? Have you had a wheel alignment yet? I'll double check the print out tonight but I'm 99% confident that I'm running about -1.5deg both front and rear.

Whaaaat? Have you had a wheel alignment yet? I'll double check the print out tonight but I'm 99% confident that I'm running about -1.5deg both front and rear.

Well there's two columns on the report they gave me - "Diagnosis" and "Adjustment". My guess is that it's the Adjustment column (as follows)..

Front

Partial Toe: Left 0,8 Right 0,6

Toe: 1,4

Set back: -0°28

Camber: Left -1°52 Right -1°58

Camber dif.: +0°06

Caster: Left +6°58 Right +6°34

Caster dif.: +0°24

King pin: Left +7°22 Right +6°40

King pin dif.: +0°42

Included angle: Left +5°30 Right +4°42

Rear

Partial Toe: Left 1,0 Right 1,0

Toe: 2,2

Camber: Left -1°56 Right 1°58

Camber dif.: +0°02

I realised two things while typing that out.

1. I need to find my scanner.

2. You might have been referring to combined left and right camber on your car?

Just double checked mine. Not quite as bad as I thought but the rear is too much.

Front camber is L -2.09deg R -1.22deg

Rear camber is L -2.06deg R -2.01deg

The rear i would like at -1.00deg most and front I want to even it up at -1.22deg both sides. I installed offset bushes up from to help an waiting on the SPC offset bolts for the rear. Then I'll take it somewhere else and get it aligned again

Where did you get yours done?

Where did you get yours done?

Adelaide Radial Tyre at Holden Hill. They do a lot of motorsport cars and seem to have a very good reputation. They kind of dicked me around with times but the work was good and the price wasn't too high. :laugh:

Dealt with them on a business level before. I think I'll give them a miss and go back to Pedders at ridgehaven. Didn't have time to get to pedders when I had the m35 done and went to tyre power on north east road.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...