Jump to content
SAU Community

Recommended Posts

I rolled mine with a 70mm pipe then gentley smahsed the f**k out of them with my 4pound snap destroyer cold blow hammer.

beeeeeeeyaaarrtiiifoool

FINE PRINT - YES it took me around 3 hours to then reapir each of them and shape them pissing around with my slapper hammer and various dolley's and contour guages, and then almost a full respray hahaha

post-47373-0-51785800-1324413868_thumb.jpg

well mine are a lot worse than Jacks, I'm a little disapointed, I couldn't see the damage that was being done until I stood up and the light hit it, looks like a retard has assaulted it with a bb gun -__- oh well, they're only guards on a drift car :P

you can't tell in the pics though! hehe. Pulled the fronts out about 20mm. I might have to spend the next 3 hours reapiring each of them and shape them pissing around with my slapper hammer and various dolley's and contour guages, and then almost a full respray

_1010033Medium.jpg

_1010034Medium.jpg

_1010032Medium.jpg

Edited by zoidbergmerc

looking at that lip though...they still dont fit? :blink:

i mean, youve fuarked the guards already, so might as well make them so they definitely wont shred your valuable slicks?

It's just the angle of the photo, it should be OK. Going to nubco now to get a bigger pole to pull it a little more just to be super sure. Looking at some old gopro footage, looks like the front wheels travel about 70mm so I'm trying to accommodate for that.

I'm going to raise the nose up another 10mm too, looking at the car side on, looks like it's under brakes already :P

Interesting tid bit.

I had my car on the turnplates and beaurepairs the other day and it got 41 degrees of steering angle (not sure what stock is, quick google suggests it's 36 degrees). Only mod is these http://www.gktech.co...uctID=NISS-TROD

They're good gear, I'd reccomend them to anyone with a skyline even if you're not drifting, just makes moving around so much easier, I can do u turns in the street and drive straight into my garage because of them :)

Edited by zoidbergmerc

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...