Jump to content
SAU Community

Recommended Posts

Ok guys heres the story.

A few months ago i had a pretty stock R32 GTR.

Only mods where the exhaust, 33GTR N1 Turbos (not the BB type Garrett 2860-7) and a Boost controller. I Took it to the 1/4 mile and ran a best time of 12.997 @ 105mph.

Which i was happy with. Seemed right with those mods.

But then i decided to put a bit of extra stuff in. So i chucked in

2x Garrett 2860-7 turbos

Kelford 272deg cams + head work

Tomei cam gears

PE 750cc injectors

PE Kevlar timing belt

Walbro fuel pump

Tomei fuel rail

Stainless steel manifolds

Apexi dual intake kit

stainless steele radiator

Bee*R launch controller

and a power fc.

Got it all put in and the tuner did a rough Road tune with the PFC. He did suggest however that i get a dynotune. (but the powerfc i bought was already tuned for those turbos)

Now i just got back from the drags and after doing multiple runs, ran a best time of 13.451 @ 102mph. uughh. wtf?

Can anyone help me out?

Edited by NOCTIS
Link to comment
https://www.sau.com.au/forums/topic/353439-spent-8k-on-mods-only-to-go-slower/
Share on other sites

edit: Hmm just had a quick look. And i found quiet a large split in the intake hose that runs into the intercooler from the turbos.

Which would make sense cos i found i was losing alot of power in the higher rev ranges.

shit...

Iv been driving the car pretty hard all week. hope nothing else have fkd up on it.

Edited by NOCTIS

I count at least 6 items on your shopping list that were not needed and wouldn't have improved your horsepower.

Get the car on a dyno and have a proper tune done if you want to realise the full potential of your new setup, hoping for the best with a used Power FC that you were told was tuned for a specific type of turbo is a royal gamble.

+1 cams too big.

Realistically It feels more like you have simply tried to tune the car rather than perform any significant upgrate. I see the -7s as a steel wheeled stock turbo, not SIGNIFICANTLY better (people will hate me for the comment) and you already had that as such with the N1 turbos.

The only other power getters I see are the cam gears, manifolds and intake kit. The only one actually doing some work IMO is the cam gears which is negated by the oversized cams. The manifolds and intake kit would yield minimal results at best with the -7s.

All in all I would expect the current setup to be slower than if you had simply added the PFC + camgears.

Not to be a prick or anything, I hope you take the above as constructive and make some minor revisions to your efforts. Goodluck.

tuner did a rough Road tune with the PFC.

He did suggest however that i get a dynotune.

Now i just got back from the drags and after doing multiple runs

srsly... wtf are you doing man?

I'm not after 500hp+ that's why I went with the -7. The 33gtr n1 uses journal bearings which don't spool as fast as the 34 n1's. I swapped the manifolds as it was something I might as well do while the turbos are out anyway.

All I want Is a good balance between response and top end at around 400ps. Which is what I would have thought the -7s and the cams wouldv given me.

And the tune isn't that bad at all for your information. I just got recommended to get it dynotuned to get the most out of the mods. Not because it's going to blow up in my face if I leave it on idle.

+1 cams too big.

Realistically It feels more like you have simply tried to tune the car rather than perform any significant upgrate. I see the -7s as a steel wheeled stock turbo, not SIGNIFICANTLY better (people will hate me for the comment) and you already had that as such with the N1 turbos.

The only other power getters I see are the cam gears, manifolds and intake kit. The only one actually doing some work IMO is the cam gears which is negated by the oversized cams. The manifolds and intake kit would yield minimal results at best with the -7s.

All in all I would expect the current setup to be slower than if you had simply added the PFC + camgears.

-7's a big improvement over the N1's... they're listed as R33 N1's not R34 N1's

cam gears need to be dialed in on a dyno too (as well as a PROPER tune, but that's already been stated)

You ran a 13.0 at 105mph so that's normal for a 32 GTR with an exhaust.

So just tuning those N1 turbos with an aftermarket ECU would have got you good gains.

Since you went all out - then you'll need a tune, especially with those cams. Don't expect anymore overall power from the cams with those turbos, just a shift to higher rev range and less torque.

Yeh im booking it in for a dynotune right now, and just ordered a new pipe to replace the split one. Yeh I dunno. I was just excited to have the car back I guess. So I couldn't help driving it.

So I'm back to driving the bunky around now.

yeah not exactly a good result. my 32 with stock turbos, stock manifolds, stock injectors, stock cams, stock intercooler, basically 100% standard except for a cat back exhaust, 1 bar boost, and a well tuned power FC ran a 12.4 qtr mile. GET IT TUNED asap. it should be mid to high 11s at this point.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 2: Today I'm f**king pissed. Some of you probably saw my thread that I opened shortly after joining this forum, "urgently need expert/experienced opinion", in which I discussed the possibility of a porous RB26 engine block which I also found hard to believe. Currently both turbos are out since the shitty braided line that was installed by whoever fitted the GT28 turbos leaked oil onto the exhaust. Today while working on the cam covers to put new gaskets and half moons in, I cleaned the side of the engine block with brake cleaner. Some time later I saw that it was still glistening with oil or coolant so I dried that off. But it was wet again shortly after. Verdict: I'm royally screwed. What you can see here (hopefully, despite shit resolution), circled in red, is a crack above the turbo oil feed. Extent is a few cm long and basically goes from #3 cylinder wall to #4 cylinder wall. It slowly lets coolant through, even without any pressure behind it. I am absolutely dumbfounded as to how this crack even formed, especially since it isn't along the cylinder as it usually is but rather a horizontal crack. Probably a few cm in length. Not sure on how to deal with this issue right now. Most likely, the only true fix is a new engine block, and even a relatively well done temporary fix requires at least a full engine teardown. Neither of those really fit my timetable right now, the car has been in my buddy's garage long enough as it is. I'm open to suggestions, but I'll be looking into ordering a new 05U block soon so I have one ready for the coming year, or whenever the current block inevitably fails fully. (Most likely once the crack reaches one of the frost plugs) I think it'd be a waste of money and time to rebuild the engine with this block. Oh and I found a rust hole on the side pocket of the trunk, which someone covered up with sealant goop, a piece of number plate and bodywork filler. Fun times. So far for every issue we fix we just find a new one that is arguably worse.
    • I have not found this no. I put one back on a couple days ago with no drama. I agree they are tight, but no need to remove anything. 
    • That is gates blue racing belt
    • Anyone found gates blue racing to be extremely tight/ almost impossible to install without moving the exhaust gear
    • Hello am apex am new here and also thanks for helping registering the forum 
×
×
  • Create New...