Jump to content
SAU Community

Recommended Posts

Just wondering what everyone's running on their boats.

When I had new KU31's put on (245/40/18) my steering went all heavy and crap at low speed. At first I thought the tyres must be underinflated...

Went to the servo, fronts were at 34 and rears at 36. Pumped all 4 to 39(!) Is this too high?

Now I realise the increased tyre width probably has more to do with it....right?

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/
Share on other sites

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

read the pressure rating of the tyre. it will have a maximum. but too high will cause excess wear in the centre, an underinflated tyre will wear onthe outside.

a too firm tyre will be bumpy, especially with aftermarket suspension. i think i run mine at 38 front and 36 rear. but this is when cold. always check when cold

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5749475
Share on other sites

I was runing 34psi but after a run down Putty road on the weekend it was too rough with the coil overs. So on the return trip, i lowered em to 28psi. Car was much better to drive and not quiet as rough. Still handled the corners beautifully!!

I run these tyres: http://www.falkentire.com/Tires/Passenger-Car/Azenis-RT-615K-14

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5749569
Share on other sites

i like that test.

but yep, i run 38 front and rear - tested when cold.

good investment is a digital pressure gauge. dont trust the ones at the servos. i check pressures weekly. car feels nicer and less jittery over low speed bumps when the pressure is down around 36 (which is what most tyre places will reccommend) but i reun a slightly higher pressure to protect the wheels, and to counter some of the camber wear by rounding the center of the contact patch.

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5749929
Share on other sites

Just wondering what everyone's running on their boats.

When I had new KU31's put on (245/40/18) my steering went all heavy and crap at low speed. At first I thought the tyres must be underinflated...

Went to the servo, fronts were at 34 and rears at 36. Pumped all 4 to 39(!) Is this too high?

Now I realise the increased tyre width probably has more to do with it....right?

I run 38 - 40psi but I believe your heavy steering is caused by the wider rims/tyres and different offset. It gets worse the wider you go.

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5749977
Share on other sites

That's all horribly low for low profile 18's...

I run my 235/40/18's at 45psi cold, even 42psi doesn't feel right and anything under 40psi feels terrible.

You must have good suspension to compensate your tyres which are as hard as concrete!!

Must be bloody slippery in the wet/rain with those pressures.

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5750078
Share on other sites

50psi!? that is ridiculous. and why would you run it higher if you're lashing it? should be running it lower if anything. otherwise it just turns into a roller skate - you will get better grip with lower pressure, plus it will allow for expansion of the air as the increased heat levels build.

only people i know who run those pressures are the VIP guys who run super stretched tyres and huge camber - helps prolong tyre life and keeps the tyre seated on the bead.

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5750128
Share on other sites

50psi!? that is ridiculous. and why would you run it higher if you're lashing it? should be running it lower if anything. otherwise it just turns into a roller skate - you will get better grip with lower pressure, plus it will allow for expansion of the air as the increased heat levels build.

only people i know who run those pressures are the VIP guys who run super stretched tyres and huge camber - helps prolong tyre life and keeps the tyre seated on the bead.

no

Should mention, I don't have a stagea and just realised this is the stagea section..

Edited by Ten Four
Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5750145
Share on other sites

on drift days you run a higher pressure in the rear. also some tyres are rated to 50psi. i remember a set i had on my S13, 52psi was the maximum. i ran them at 44psi.

if 50psi is over the maximum rating, youre taking a risk IMO

Link to comment
https://www.sau.com.au/forums/topic/360097-tyre-pressure/#findComment-5750151
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Echo the awesome sentiment 👍 Definitely a car worth saving. Looking forward to seeing updates as well. 
    • Scenic roads, stunning skylines, and Chickos to finish it off! Join SAU NSW as we cruise through the Royal National Park and along Lawrence Hargrave Drive to Figtree! Sunday 26th October 2025 4:30PM Meeting Waterfall Station Parking 5:00PM Cruise Departure Royal National Park > Lawrence Hargrave Dr > Memorial Dr > Sid Parrish Park 6:15PM Arrival at Sid Parrish Park Figtree Meet Location: Waterfall Station Parking Final Destination: Sid Parrish Park RSVP: https://forms.gle/E4s5SiRKQfDdypky8 *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • It's funny, as Ive seen plenty of people use them in cheap builds on YT. And they actually go okay, even though a lot of other maxspeedingrods stuff is terrible. Those turbos seem reliable enough, the only part being, a good quality turbo that is "identical" to it, will out perform it day in and day out. In both a lower boost threshold, and the ability to flow more air at the same boost pressure. As a cheap cheap replacement, not a terrible choice. For cheap and shouldn't blow in a day, not terrible (like other eBay/Temu turbos) for low cost and still decent performance, that's where the question comes in to play from the results I've seen. I'd actually find it hilarious to buy one, and strap it to a paddock basher or some other cheap as POS originally NA car, and send it to the moon!
    • The maxpeedingrods turbo is cheap and bolts on to stock parts. I think you just need a bigger silicone coupler for the intake. Its a cheap china turbo, but it's been running on mine for almost 3 years at 16-19 psi.
    • What do they look like right after you've tried to start it with everything connected? Also post photos of what they actually look like.
×
×
  • Create New...