Jump to content
SAU Community

What Intank Pump Will Deliver The Most Flow? Nismo?

Marko R1

By Marko R1,
in Engines & Forced Induction

 Share

Recommended Posts

MagicMikeZ32 Veteran

MagicMikeZ32

Posted
Posted

Yeppers, some oem pumps are well capable of doing the job. Many z32's making 500+hp on stock pumps, however they are getting old, so a new OEM pump is always recommended :)

  • Replies 242
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Nee-san
Nee-san

I think your going to struggle to push that much power through a single pump without going to one of the really big aeromotive units or something similar marko. what's the reasoning for not wanting a

scotty nm35
scotty nm35

It's just that time of the month...

Posted Images

Marko R1 Grand Master

Marko R1

Posted
  • Author
Posted

That's pretty impressive Dean. Are u running a relay on the factory wiring?

Have u tested the pump to see how much more it has got and what it could potentially support in terms of kw?

Marko R1 Grand Master

Marko R1

Posted
  • Author
Posted

It was a full factory setup, factory wiring, like it had never been opened.

I've got twin nismos now so I can't compare....

Why did u upgrade your pump? Making more power or for safety factor?
Marko R1 Grand Master

Marko R1

Posted
  • Author
Posted

I think I've hit a wall as I cannot source submersible fuel hose with an ID to accommodate the fuel pump inlet which is 15mm. I tried pirtek, gates, speed flow, earls and purple pig.

Gates stock submersible hose in 2 sizes and these only run up to 9.5mm.

Does anyone have any ideas on the best way to mate my fuel sock to the fuel pump? Fuel pump is a push hose fitting and the fuel sock has a female push fitting with an ID of 24mm. The generic fuel hose does infact work in terms of size for ID and OD, however, the outer skin will disintegrate as it sits in the fuel tank.

If I have no other option, I may run speedflow -10 push hose as EFI Performance suggested this and apparently does not break down in fuel (even though speedflow stated to me that it is not rated for fuel submersion.

SiR_RB Grand Master

SiR_RB

Posted
Posted

When I bought my car the previous owner said it had a bosch 044

Had it tuned running 340rwkw no fuel supple issues what so-ever, even went drags 3 times etc

Upgraded last month to a walbro e85 pump only to find it had a stock pump in the tank lol

Marko R1 Grand Master

Marko R1

Posted
  • Author
Posted

When I bought my car the previous owner said it had a bosch 044

Had it tuned running 340rwkw no fuel supple issues what so-ever, even went drags 3 times etc

Upgraded last month to a walbro e85 pump only to find it had a stock pump in the tank lol

Its amazing what flow these OEM pumps can support. I might test mine in a bucket and see how many litres it flows over 1 minute...what is the best way to test this though, direct to the battery?

Marko, just cut off some hose off a fire truck. She'll be right mate ;)

how about some seasoned bong hose? Loool
Marko R1 Grand Master

Marko R1

Posted
  • Author
Posted

I want to do back2back flow testing with the OEM pump and pierburg. I reconnected the OEM pump but the trigger switches it off after 5 sec.. can I connect the pump to the battery direct as I want to measure flow into a bucket over a period of 1 minute so that I can calculate LPH.

Marko R1 Grand Master

Marko R1

Posted
  • Author
Posted

Update time.

I decided to flow test my OEM pump direct from the battery and was very surprised by the results.

Over a period of 30seconds, it flowed 2.7ltrs which equates to 324LPH.

The pump even ran low and started blowing bubbles as I couldn't fill up the 2 ltr bottle it was sitting in quick enough.

Am I getting a higher voltage / power supply from the battery, rather than the fuel pump harness located in the boot? How can the pump flow at such a rate?

r31 25t Contributor

r31 25t

Posted
Posted

Off the return, that way the fpr will hold it at the correct pressure/restriction. It should be a reasonable indication of the flow as long as there are no other restrictions. Eg. Blocked fuel filter crimped line ect.

  • 2 weeks later...
B-rice Mentor

B-rice

Posted
Posted

just wondering

are stock 34GTT pumps enough to use as lift pumps for a surge tanks with two 044s. This is for 350kw+ on e85

or would using the Deatschwerks 300lph as a lift and two 044s be overkill/enough?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Cas issue

      By GTSBoy · Posted

      The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Duncan
      RB26DETT Sketchy boost mod?

      By Duncan · Posted

      Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • nxh
      R34 4 door side skirt identification

      By nxh · Posted

      Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...