Jump to content
SAU Community

Recommended Posts

Yeppers, some oem pumps are well capable of doing the job. Many z32's making 500+hp on stock pumps, however they are getting old, so a new OEM pump is always recommended :)

That's pretty impressive Dean. Are u running a relay on the factory wiring?

Have u tested the pump to see how much more it has got and what it could potentially support in terms of kw?

It was a full factory setup, factory wiring, like it had never been opened.

I've got twin nismos now so I can't compare....

Why did u upgrade your pump? Making more power or for safety factor?

I think I've hit a wall as I cannot source submersible fuel hose with an ID to accommodate the fuel pump inlet which is 15mm. I tried pirtek, gates, speed flow, earls and purple pig.

Gates stock submersible hose in 2 sizes and these only run up to 9.5mm.

Does anyone have any ideas on the best way to mate my fuel sock to the fuel pump? Fuel pump is a push hose fitting and the fuel sock has a female push fitting with an ID of 24mm. The generic fuel hose does infact work in terms of size for ID and OD, however, the outer skin will disintegrate as it sits in the fuel tank.

If I have no other option, I may run speedflow -10 push hose as EFI Performance suggested this and apparently does not break down in fuel (even though speedflow stated to me that it is not rated for fuel submersion.

When I bought my car the previous owner said it had a bosch 044

Had it tuned running 340rwkw no fuel supple issues what so-ever, even went drags 3 times etc

Upgraded last month to a walbro e85 pump only to find it had a stock pump in the tank lol

When I bought my car the previous owner said it had a bosch 044

Had it tuned running 340rwkw no fuel supple issues what so-ever, even went drags 3 times etc

Upgraded last month to a walbro e85 pump only to find it had a stock pump in the tank lol

Its amazing what flow these OEM pumps can support. I might test mine in a bucket and see how many litres it flows over 1 minute...what is the best way to test this though, direct to the battery?

Marko, just cut off some hose off a fire truck. She'll be right mate ;)

how about some seasoned bong hose? Loool

I want to do back2back flow testing with the OEM pump and pierburg. I reconnected the OEM pump but the trigger switches it off after 5 sec.. can I connect the pump to the battery direct as I want to measure flow into a bucket over a period of 1 minute so that I can calculate LPH.

Update time.

I decided to flow test my OEM pump direct from the battery and was very surprised by the results.

Over a period of 30seconds, it flowed 2.7ltrs which equates to 324LPH.

The pump even ran low and started blowing bubbles as I couldn't fill up the 2 ltr bottle it was sitting in quick enough.

Am I getting a higher voltage / power supply from the battery, rather than the fuel pump harness located in the boot? How can the pump flow at such a rate?

Off the return, that way the fpr will hold it at the correct pressure/restriction. It should be a reasonable indication of the flow as long as there are no other restrictions. Eg. Blocked fuel filter crimped line ect.

  • 2 weeks later...

just wondering

are stock 34GTT pumps enough to use as lift pumps for a surge tanks with two 044s. This is for 350kw+ on e85

or would using the Deatschwerks 300lph as a lift and two 044s be overkill/enough?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...