Jump to content
SAU Community

Nitto Headgasket Failed What Should I Use

grygtr

By grygtr,
in Engines & Forced Induction

 Share

Recommended Posts

Walk510 Enthusiast

Walk510

Posted
Posted

firstly define hi boost ? were your running head studs ? and yes what was the deck roughness like ? even though in the " race engine builders hand book " they say "the gaskets surfaces must be near polished, the problem is there must be some tooth to retain the gasket its a fine balancing act"

r33_racer Grand Master

r33_racer

Posted
Posted

Even head gasket manufacturers state pretty fine Ra, ive seen anywhere from 50-60 RA or finer, some have even stated 15 or finer. The smoother the better, any protruding ridges from machining marks(noticed more so on rougher finish) will chew the gaskets as it expands and contracts, especially when its wedged between two dissimilar materials.

But as everyone else stated, headgaskets blow for a reason. Fix that issue and it wont blow again.

Supa Steve Enthusiast

Supa Steve

Posted
Posted

How did the engine fail? It wasn't from excessive cylinder pressure lifting the head, breaching the head gasket, hydrolocking a cylinder and bending/or throwing a rod?

My engine builder uses Nitto gaskets and has pushed them a long way without issue, maybe another factor influenced the damage.

The Dan Grand Master

The Dan

Posted
Posted

People shitcan Commetic gaskets as well but we've run them without a single problem in boost apps exceeding 30psi. 26psi for 2 years straight racing.

Nitto are a better gasket IMO. I think you're missing something

D_Stirls Veteran

D_Stirls

Posted
Posted

People shitcan Commetic gaskets as well but we've run them without a single problem in boost apps exceeding 30psi. 26psi for 2 years straight racing.

Nitto are a better gasket IMO. I think you're missing something

As you would know, that's cos' people don't prep' BOTH the surfaces, and then they blame the gasket when it leaks?

To the OP, as has been asked did you prep' both the surfaces to the correct spec's?

Beer Baron Grand Master

Beer Baron

Posted
Posted

yeah as above, most MLS gaskets are pretty stout and there may be another issue. but i've got plenty of experience using tomei head gaskets personally and never had a problem. they are very high quality and have lasted through plenty of heat, power and kms. I'm always happy using tomei.

sinistaGTR Grand Master

sinistaGTR

Posted
Posted

yeah as above, most MLS gaskets are pretty stout and there may be another issue. but i've got plenty of experience using tomei head gaskets personally and never had a problem. they are very high quality and have lasted through plenty of heat, power and kms. I'm always happy using tomei.

I had a acl one fail straight away after a rebuild on my old 33. Ordered the tomei and it was gold.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...