Jump to content
SAU Community

Recommended Posts

  • Replies 163
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Wheels...what wheels.

Both the LHS have bits missing off them pinch.gif

All the arms are back on the car and it drove ok. Just needs a wheel alignment now. I'm guessing the front LHS hub and mounting points for the tie rod and the lower arm may have moved a little.

But time will tell.

Lol did anyone actually read the new supp regs in regard to the fire ext. mounting? Not sure if this has come directly from CAMS (wouldn't surprise me!) but the supp regs read:

b) Must be fitted with a fire extinguisher securely mounted on a metal bracket with metal straps within the cabin and readily accessible to the driver whilst still in the seat belt or harness and which complies with AS 1841 (save that extinguishers which meet AS 1841.2 are not permitted), and be of at least 900gms capacity. Halon/BCF extinguishers are not permitted. The extinguisher and the bracket must be a compatible set, (i.e. as supplied by the manufacture of the extinguisher.) The extinguisher should be retained within the bracket by at least one (1) metal strap. The bracket should be secured using a minimum of 2, Grade 6 or greater bolts, of a minimum 6mm diameter, and self - locking nuts. A suitably sized body washer may be required to provide extra support for the bracket. The securing system must be able to withstand a 25g deceleration.

The part in question is the bit in bold regarding Grade 6 bolts. There is probably no way that the scrutineers on the day are going to check the markings on the heads of the bolts 8), but the problem is that grade 6 bolts are no longer made and herein lies the problem....The supp regs say grade 6 or greater, but the next grade of bolt is the grade 8. Sure this is a 'harder' bolt but is prone to breaking due to the brittle-ness from the treatment ie under load it is more likely to shear the head off. The lower grade 5 is the bolt used in automotive apps as it is still 'hard' but due to the lower level of heat treatment is more likely to stretch under load rather than shear.

So bottom line, I'm going to use grade 5 or 8.8 bolts....

lol @ self tapper.

Have a read of the entire reg though Ant, its all pointless anyway/not ever followed.

There is no chance in the world, strapped into a harness, that you'll be able to reach the extinguisher unless its bolted to the roof above your head!

Given the purpose of a harness is to stop one from moving!

Have a read of the entire reg though Ant, its all pointless anyway/not ever followed.

There is no chance in the world, strapped into a harness, that you'll be able to reach the extinguisher unless its bolted to the roof above your head!

Yeah I know....but I'd be kicking myself if I turned up, paid the money and they knocked me back because of something so small :(

Hy Ant, what's your previous best at Sandown?

Sandown makes me scared so prev setup only yielded a flat 1:23. While I will be aiming for teens, I will be held back by the fact my balls are smaller than usual at Sandown :yes:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
×
×
  • Create New...