Jump to content
SAU Community

  

93 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

  • 2 weeks later...

tacho mate. Maximum tune style lol

:thumbsup:

IMO unless you do this then you are either limiter bashing or not getting peak HP.

otherwise if you are just cruising around then why would one need anything other than just a general feel. Doesnt really matter if it goes to 2800rpm or 3500rpm at 1/3 throttle really does it...? But thats not really the scenario for this quesiton is it?

Edited by jjman

I use to use feeling, but since i just got my skyline and have only driven it once, i used the taco and feeling, only until i get a feel of things

taco.jpg

Edited by Miguelone

R34 in tiptronic mode - usually 4000rpm to 6000rpm. Driving easy auto shifts around 2000rpm to 2500rpm

IS200 (manual) - I generally shift on sound and feel, except on steep hill starts - I use the tacho. Normal driving shift around 2500rpm to 3200rpm. Down hill I shift at 1800rpm.

Datsun bluebird - 4000rpm

I tell usually by sound at lower gears and tacho at higher gears, and in practice (on the street) I always short shift before 5000rpm. I probably exceed 5000rpm about once per week at most (daily driving). Can't remember the last time I went past 6000rpm, on the street it just isn't required (theoretically it would be required for a drag race).

On the street in 1st and 2nd gear with any sort of corner I short shift to get into the next gear so I can ride the torque wave through and out of the corner. This means precise throttle modulation is less of a factor and it saves a gear change and means less wear(2nd has more power but can't usually put it all to the ground). Adding bumps into the equation in Sydney just makes it even more relevant.

Just cruising I change at the point the revs start at 2000rpm -2200rpm in the next gear....or what feels right.

what's the point of having the car if you don't gun it a few times per drive?

Might as well drive a kia :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...