Jump to content
SAU Community

Range Rover Sport

RCCC

By RCCC,
in General Automotive Discussion

 Share

Recommended Posts

Johnny Veteran

Johnny

Posted
Posted

landrovers have improved much over the years but they still have their problems: electrics being the main

service is very dodgy from dealers as they will overcharge and leave certain things out: replacing brake pads but not machining discs, not reseting service indicators etc

buy from a dealer as they will offer a warranty and always purchase an extended where applicable.

range rovers are great cars, excellent to buy second hand as they depreciate and you can buy a few year old sport for almost half price from new.

macdog Veteran

macdog

Posted
Posted

I am thinking of buying a Range Rover Sport TDV6 as a second car, has anyone had any experience with this car? Its engine block is made of cast iron whereas the V8 versions made of aluminium. Any comment on its reliability, cost of maintenance, etc is appreciated.

Cheers

My old man is looking at getting something similar.

they have to be the most comfortable 4WD on the market, however you should shop around, make sure you bargin hard.

If you want to compare it to something go and test drive the Volkswagen Toureag. V6TDI or V10TDI, for what you get in terms of options they are very very generous. like Reverse camera, SATNAV, heated seats, sunroof, tow bar. 20 inch wheels.

Munro Experienced

Munro

Posted
Posted

Have you driven a BMW X5? I just bought a new Land Rover Discovery 4

for my wife ( I know thats not a Range Rover but there must be a lot

of crossover gear) The biggest difference I noticed from the X5 ( I

have had a number of BMWs) is the ride is much nicer in the land rover.

If you want a smooth comfortable ride and like the boxy look, then

Range rover is nice car.

Personally I dont like the steering/handling or throttle response compared

to the X5. The Beemers are so much more sporty, handle better and because

they are about 400kgs lighter they just blow the rovers into the weeds!

My 2c

Johnny Veteran

Johnny

Posted
Posted

They apparently also have a habit of engine oil tracking down the loom and crapping out the ECU.

lolz not sure about that one but the rear tailgate switch went after only a few years + rubber components in the suspension crack quite often and need to be replaced - this is for a discovery 3 though

warps Mentor

warps

Posted
Posted

lolz not sure about that one but the rear tailgate switch went after only a few years + rubber components in the suspension crack quite often and need to be replaced - this is for a discovery 3 though

Yes.

My brother's owned a Disco 3 for about 3 years now and it's a pig. We all advised him against it (including my bro-in-law who used to sell them brand new but gave up the agency because the warranty repairs were sending them bankrupt). The Disco has been in the shop more times than I can count, and has left my brother stranded a few times.

I wouldn't touch anything with the name rover in it. THey may be better than they were, but they are still big steaming piles of poo.

  • 2 weeks later...
tridentt150v Grand Master

tridentt150v

Posted
Posted

I wouldn't touch anything with the name rover in it. THey may be better than they were, but they are still big steaming piles of poo.

^^^^this man knows

And it all depends on what you want to do with it.......a suburban cruiser, who cares buy whatever you like, VW, Rover, X5, Jeep, Cayenne blah blah..........a real workhorse real 4wd, buy a Lancruiser, Hilux, Dmax, Colorado, Prado etc etc doesn't matter how the leather seats feel or good your ride comfort is if it stops and doesn't go between Camerons Corner and Alice Springs, you'll end up like Burke and Wills.

  • 3 weeks later...
hungry6 Experienced

hungry6

Posted
Posted

I went to test drive one "sport" awhile ago , and these are the thing that happened on the test drive.

The ABS failed and intermitently cut in. seat will not move fore or aft, and the after thee test drive

it refuses to lock up. just kept on poping open after u hit lock.

apart from that, it is a sexy looking "true 4x4"

now I'm driving a Q7.

I dont think my legs are capable of pushing one of the highway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...