Jump to content
SAU Community

Recommended Posts

No! Bad Nankangs! :domokun:

Had them on my N14 SSS, previous owner put them on. Would never, ever recommend them to my worst enemy!

Did I mention... No! Bad Nankangs! :domokun:

well to my worst enemy i might lol

No! Bad Nankangs! :domokun:

Had them on my N14 SSS, previous owner put them on. Would never, ever recommend them to my worst enemy!

Did I mention... No! Bad Nankangs! :domokun:

Nankangs FTW....they don't wear out!.....probably because they are made of a harder compound than the road they roll on!

I totally agree they are one of the worst tyres for grip that you can buy new......but sometimes that can be a good thing!ninja.gif--------> heads to youtube for another laugh of the stall and launch!

Nankangs FTW....they don't wear out!.....probably because they are made of a harder compound than the road they roll on!

I totally agree they are one of the worst tyres for grip that you can buy new......but sometimes that can be a good thing!ninja.gif--------> heads to youtube for another laugh of the stall and launch!

I went to a trade show recently; showcasing all kinds of new automotive technology; You're all piling shit on them, but you should see the new offerings from Nanakang!

This is their new Off Road tyre; post-61153-0-69818000-1309475170_thumb.jpg

And their new Performance offering; post-61153-0-83736800-1309475227_thumb.jpg

I went to a trade show recently; showcasing all kinds of new automotive technology; You're all piling shit on them, but you should see the new offerings from Nanakang!

This is their new Off Road tyre; post-61153-0-69818000-1309475170_thumb.jpg

And their new Performance offering; post-61153-0-83736800-1309475227_thumb.jpg

hahahahahaha

Nankangs FTW....they don't wear out!.....probably because they are made of a harder compound than the road they roll on!

I totally agree they are one of the worst tyres for grip that you can buy new......but sometimes that can be a good thing!ninja.gif--------> heads to youtube for another laugh of the stall and launch!

Agree.

I am just about to replace my set for the first time... that originally came with the car!

Yes, that was 140,000kms ago lol

Agree.

I am just about to replace my set for the first time... that originally came with the car!

Yes, that was 140,000kms ago lol

You can't complain about value for money with that distance travelled, amazing! I'd put up with lower grip levels if i was to get anywhere near that wear out of a set.

My Toyos have worn the insides at the back as well. Had 2 wheel alignments in 10000km. Might be time to get a 2nd opinion

ive had my car 2 years, same rubber since i put the 18s on, the inside rear has NOT worn out and its been aligned only once since i got it. and that was after the coilovers were installed.

You can't complain about value for money with that distance travelled, amazing! I'd put up with lower grip levels if i was to get anywhere near that wear out of a set.

My Toyos have worn the insides at the back as well. Had 2 wheel alignments in 10000km. Might be time to get a 2nd opinion

I should not that the Nankangs + stock 17's were not on the car for ~30,000 of those kms.

Still, over 100,000kms from a set of tyres...

Still, over 100,000kms from a set of tyres...

I would be ecstatic if I got half that distance on a set. Didn't think it was possible actually.

I need to buy tyres in the next few weeks & you've convinced me to ask around for someone who knows how to align a M35 properly.:thanks:

  • 10 months later...

I could send you my last alignment results but they might not mean anything unless your car was exactly the same setup as mine (height wise etc).

Coincidentally I took my car in for a 5000km tyre checkup today (I was expecting another alignment & rotation) but was told to leave it another 5000km as there wasn't enough signs of wear to warrant any changes.

I could send you my last alignment results but they might not mean anything unless your car was exactly the same setup as mine (height wise etc).

Coincidentally I took my car in for a 5000km tyre checkup today (I was expecting another alignment & rotation) but was told to leave it another 5000km as there wasn't enough signs of wear to warrant any changes.

Leon, the amount of toe & camber from your alignment will be applicable, regardless of differing ride heights.

Throw the specs on if you can, if you're not scrubbing the soft Invo's; it must be on the money.

Leon, the amount of toe & camber from your alignment will be applicable, regardless of differing ride heights.

Throw the specs on if you can, if you're not scrubbing the soft Invo's; it must be on the money.

Leon, you have the toe and camber bolts though, right?

So may not be completely useful?

Good news. Still liking the Nittos?

Yeah Ryan, they impress me in different ways nearly every time I go out. Torrential rain today & it was like driving an 'ordinary' car in the dry. Wear rate could be the one thing that fails, but I won't know for a while yet.

Leon, the amount of toe & camber from your alignment will be applicable, regardless of differing ride heights.

Throw the specs on if you can, if you're not scrubbing the soft Invo's; it must be on the money.

I didn't think that would be the case, but I'll believe you. Suspension is still smoke & mirrors to me, lol.

Current FRONT specs:

Toe-in: LH 0.5mm, RH 0.5mm Total toe-in 1.0mm

Camber: LH -1.8 deg, RH -2.3 deg*

Castor: LH 6 deg, RH 7 deg

Current REAR specs:

Toe-in: LH 1.0 deg, RH 1.0 deg

Camber: LH -1.8 deg, RH -1.8 deg

* The RH camber is a potential problem. Pretty sure the Superpro upper camber kit (from Ryan's GB) will be used to reduce that figure by 0.5 deg.

I'll try to update this as my alignment guy feels his way. I've been to 2 or 3 other shops in town with no joy & at least this guy is prepared to follow through until he gets it right.

BTW, in reference to earlier posts in this thread, I also run my tyres at 40+psi.

Edited by Commsman

I got mine aligned the other day too.

Rear

Camber Left -1.04'

Right -1.00'

Total toe +1.8mm

Geometrical driving axis +0.05'

Front

Camber left -0.27'

Camber right -0.31'

Individual toe left +0.8mm

Individual toe right +0.7mm

Total toe 1.5mm

Castor left +6.32'

Castor right +6.32'

The wheel aligner said I should get the left castor on the front up to 7.0' to stop a bit of pull to the left.

  • 4 months later...

It makes me crazy /laugh when I read the first comment on this thread! So many tyre places and so called alignment guys are full of crap. Tyre guys give uneducated opinions based on NOTHING. just personal opinion. The front and rear are FULLY ADJUSTABLE so you can set them up perfectly for "australian"roads.

I have an educated opinion at least (15 years as tech engineer for Bridgestone and an engineering qualification) and we know our cars. Firstly if you can find the specs, use them. SOme vehcicles are a little different due to design (eg 350Z need more toe in because they have toe out issue under braking) or F/R balance - some FWD run more rear neg camber to give rear bite... but as a general rule: Set them up to suit your dirving needs and roads. eg i drive flat freeway but still want a bit of neg camber for cornering - so half to 1 degree of neg camber, put a bit of toe in for movement of bushes, under braking and wear (1mm measured on the right tyre /wheel diameter).

Re tyre pressures, if you are running 45 series or lower put 40 psi because they are easily damaged if they get a little underinflated. esp if they are subject to excessive camber. the lower the aspect ratio - the more pressure for safety (up to 45). I run 38 in my 50 series, I would not go under 34.

Re tyre wear, how long is a bit of string? depends on alignment and driving. I will get at least 45000 out of mine because I do a lot of freeway. You get what you pay for with tyres. Nankangs and wanlis etc just dont have the balance of grip and wear and are really bad at recovery (slalom). I remember testing wanlis on a reps HSV. I nearly lost the rear end by the 3rd cone and had to abort at 70km/h whereas Bridgestones did 80km/h and just kept going where I pointed them - no snap oversteer no wash - just grip.

But if you like power oversteer coming on easily, and dont mind fighting for your life dodging a kangaroo or animal when the tyre wont recover, go for the wanlis!

i took my car to pedders for a check up about a month ago i thought the inside rear edges were wearing because i have -2 degrees of camber but the guy reakoned it shouldnt wear like that and that my rear front X'member bushes were flogged.

but ive gotten over a years worth out of them and i think about 25,000km so im not complaining really.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...