Jump to content
SAU Community

Recommended Posts

hi guys i recently purchased a s2 r33 96 gtst and am a bit worried about the way that it drives so il give you the story and hopefully somebody can help me.

Ok i when i got it it was LOW like on the bump stops low had aftermarket suspension KYB i think was flogged out. When i hit bumps on the road the rear of the car would kind of kick out sideways ( that i understand becuase all that energy has nowhere to go)

So to solve the problem i brought a set of genuine coilover of this forum and the guys assured me that they were mint and working perfectly.

So on the weekend me and a mate went to his workshop and fitted them (he is a mechanic) and the underbody of the car looks great and all the bushed look fine aswell.

After fitting the used genuine coilovers i was very dissapointed as the car sits fine now but the shocks are f**ked the car just bounces like crazy and going fast around a corner the rear just bounces across the road.

But here is my question when i hit bumps still the back kicks out just a little no where near as bad as when it had no suspension but still just little, and im done with seconhand shit so i brought brand new adjustable coilivers and will fit them on the weekend.

Is it possible that the rear cradle is moving sideways or just a case of rooted suspension all round, i like this skyline appart from that and i dont want nothing fancy i dont race etc or should i just sell it?

Link to comment
https://www.sau.com.au/forums/topic/369815-r33-bad-handling/
Share on other sites

sounds like you bought jap coilovers that have way too stiff spring rates for our roads. there probably wasnt anything wrong with them other than that they were unsuitable for what you want them for

Na i had a look underneath it, was sitting on bumpers just wondering why back is kicking and unstable over bumps.

Get a wheel alignment. If the car was so low it was on the bump stops bfefore and now its at standard height your settings will not be the same.

Get it aligned and start again. I have a stock series 2 and it handles and rides just fine.

yes i know that, i have new coilovers and new tie rod ends going in on saturday then il get a wheel alignment on the following monday, my questions is why is the rear UNSTABLE as hell and kicking out, will new coilvers fix the problem or should i be looking elsewhere for the issue, and all the bushes are fine.

yes i know that, i have new coilovers and new tie rod ends going in on saturday then il get a wheel alignment on the following monday, my questions is why is the rear UNSTABLE as hell and kicking out, will new coilvers fix the problem or should i be looking elsewhere for the issue, and all the bushes are fine.

When it was super low, you would have had bump steer. That is, hit a bump and the rear wheels will actually change alignment so much it "kicks".

Now that it's raised, your rear toe and camber will be so far out, it's not properly gripping in the back, and it's just moving around.

As has been said. If the car was sitting on the bumps stops it was FAR to low for a Skyline to handle properly. Once a Skyline gets that low the suspension geometry goes to shit.

You then put in different suspension which im assuming raised the car back up? Or did you simply reuse the old springs and put in new shocks? Because that would have been pointless.

So if the car is back to normal ride height than you will now need a proper wheel alignment as you have changed the suspension geometry again.

New suspension will not fix the problem if your alignment is completely out of whack.

Also you havn't said what springs rates any of the spings were. As was mentioned, if they were Jap branded they could have been ridicolously stiff which in conjunction with a very low car would result in poor handling on the street.

raising the car will make the rear toe in

excessive toe in at the rear will make it very unstable exactly like you've described

so like what others have said

wait til you get an ALIGNMENT

problem will most likely go away

i thought excessive rear toe out would make it supre unstable, and toe in would stablise it?

or is it just any excessive toe makes a car unstable?

i thought excessive rear toe out would make it supre unstable, and toe in would stablise it?

or is it just any excessive toe makes a car unstable?

Yeah I thought raising the car would make it toe out and gain positive camber which would cause the problems OP is having. Either way, alignment is necessary. They're like $40, stop being a tight wad and get it done.

You'll get toe out at the front and toe in at the rear when you raise the car

Look at it this way

Both front and rear are designed to toe in under hard braking to stabilise the car

But because when you step on the brake hard, front dives, rear lifts

So nissan had to design the Front and rear geometry to act completely opposite

Yes toe in helps stabilizing it but not when it's too much

Edited by chiksluvit

i have the same issue on my car atm too (R34 GTT), i believe it is for the 2 following reasons;

1) rear shocks are dead as they are leaking (but not knocking)

2) toe needs to be adjusted as the last time i got a wheel alignment, it was out by heaps.

I had stiff coilovers before (G4s) and it handled perfectly so i dont thkn stiffness will be the cause of it.

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...