Jump to content
SAU Community

Recommended Posts

That's if you don't count today or Friday, = 3 days.

Btw, for sale, single bed from Friday to Sunday.

Goulburn valleys motor village. $60 dorra

might be interested ..why you not staying

good work man. doesnt it ive you reason to just leave it and avoid problems? lol

Yes and no! It will be higher than it was for track purpose... 2-way, exhaust, steering wheel are all going back in this week

At the moment it sits as high as Alex's car haha

Not really.

Was curious cause if you do lower your 34, it really shouldn't sit that low and it'll well within legal height.

The problem with my car is that the exhaust its really low. Came like that from the land of the rising sun.

At the moment I would say the gap between the tyre and guard is about 5cm just to clear the 100mm clearance....

The problem with my car is that the exhaust its really low. Came like that from the land of the rising sun.

At the moment I would say the gap between the tyre and guard is about 5cm just to clear the 100mm clearance....

Change your exhaust brah.

Sell your current exhaust and give or take $100, get a better fitting exhaust.

Change your exhaust brah.

Sell your current exhaust and give or take $100, get a better fitting exhaust.

Have thought about it, but don't want to spend anymore on the car than I have to I guess. Also was getting pretty bad wear on the inside on the tyre when it was lowered and is my daily driver.

At one stage I be mirin those racepace exhausts. Then I saw the price tag and cried.

Have thought about it, but don't want to spend anymore on the car than I have to I guess. Also was getting pretty bad wear on the inside on the tyre when it was lowered and is my daily driver.

At one stage I be mirin those racepace exhausts. Then I saw the price tag and cried.

I feel you meng.. but not in a priest way

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...