Jump to content
SAU Community

Recommended Posts

Council wants a guy to get rid of 10 Japanese sport cars that are across his resoviour house property.

Spotted a few r34 gtt's, r33's Silvia's etc....

All registered or more like not registered?

And rich kent.

Grant, is this the 'sell your GTR week?'

Kinda, but won't do this week, need new indicators as I broke orange ones d'oh!

Still need to mount the plates into the bumper.

Hmmm is it near Northland shopping centre? I know of an importer there and its junky as fuck

most cars have been there for years cause they are shit as too

i'd tell em to get f**ked.

All registered or more like not registered?

And rich kent.

Not sure it was just a 10sec preview to tommorow night's 6p.m news

Think he was showing the reporter under the bonnet of one of the R34's.

Don't get home from work by that time but am curious if they paint him in a bad light or not. Becuase if he has that many imports he must be a hoon...

i want to sell my car, moving my details to my uncles in perth, going for my wa license and buying another turbo... if it wasnt that much of a head f**k i would have done it in a flash

damn you ric :( i wants power now

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...