Jump to content
SAU Community

Recommended Posts

Age Excess?

Pat, you still under 25?

And fuck that vehicle Excess, so shit!

only 23. Couple more years to go!

Revzone +1

They my main workshop. Do a great job although a bit more pricey, their service and delivery you can't fault. They have a hub dyno though

Telemarketer: Hello can I speak to the business owner

Me: Speaking...

Telemarketer: Hello sir I am from Telstra, the reason I am calling is because I want to save you money on your monthly phone account

Me: I don't have a phone

Telemarketer: *silence*

Telemarketer: How am I speaking with you right now?

Me: GET OUT OF MY HEAD

Bahaha awesome.

you can get spare parts from taxi wreckers

so this is no surprise!

hahaha

Haha, was eyeing off the throttle body setup when I was there getting tyres @inverse on Saturday. So want itb's on a 20 haha

can only be done with a custom made manifold piece to the itb's iirc? lots of work/$$$ etc

Bit of rust in the beaver panel.

Should I cut it out and fill it with brass.

umm no one fills with brass man

there's nothing you can do to it that wont make it look like a typical try hard bogan mobile

so just leave it stock and clean

Aaaah yes, the dreaded falcadore bogan potential. Never thought about that issue tbh.

hahaha

can only be done with a custom made manifold piece to the itb's iirc? lots of work/$$$ etc

umm no one fills with brass man

Pretty sure some peeps fill with it.

Either way searched and looked dodge.

Need to find out what thickness steel, got a metal bender and shit at work. Can't be that hard to Make some steel to fit.

lebo...

haha that's for sure :P

Pretty sure some peeps fill with it.

Either way searched and looked dodge.

Need to find out what thickness steel, got a metal bender and shit at work. Can't be that hard to Make some steel to fit.

yeah full dodge, like doing any filler to cover rust

just have a panel made or get a wrecker to cut one of a wrecked car and weld back in (this is just more effort than new panel though)

Alex did you go to the JDM meet last week?

Heard over 200 cars? True or exaggeration?

Close. possible. they opened up the bit where the wharehouse is for more cars

Pic. more cars on the left behind the truck too. and all along the driveway

6912903495_04a5395ffa_o.jpg

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...