Jump to content
SAU Community

Recommended Posts

How's the new job?

Yeah good, damn busy though with less than a month to the first deadline. Going well, and will get a lot of good experience. The train trips suck though.

My job doesn't allow me any SAU time. I know I don't have the 33 anymore but its a good community, too many douchebags everywhere else.

I sold my 33 back in 06 :D

Destroy VX SS in a rolling...he does loser fly by as I go heavy on the brakes and a VE SS playing catch up on us both flies through the 10 metre gap between us at ~150km/h, then nearly loses it around the upcoming corner, farkin nutjob!

did you go last year? i went this year effing loved it but it was my first time i had a ball at the stalls alone, but i reckon next year ill get pretty bored

I don't think this year was quite as good as last year. Not sure if I'll head up again in 2013 yet.

Destroy VX SS in a rolling...he does loser fly by as I go heavy on the brakes and a VE SS playing catch up on us both flies through the 10 metre gap between us at ~150km/h, then nearly loses it around the upcoming corner, farkin nutjob!

I'll go a rolling with ya in about a month :P

*on my private airstrip*

is it because Rota? or because you had stupidly stretched tyres over them which wouldnt take the shock of any potholes.

ive hit heaps of pot holes purely because i cbf going round. no issue with mine.

I've had two sets of Rotas, both have served me absolutely fine.

I'll go a rolling with ya in about a month :P

*on my private airstrip*

Screw rolling, I'll have my Nittos by then...we can do it off the line muhahaha. Dat 1st gear usability.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...