Jump to content
SAU Community

Recommended Posts

no you dont, all you need is a thermometer, hot water and an esky ;)

sous-vide almost all my red meat and a lot of other stuff at home, and I dont have a controller

Nah, would be less... even with the capability to have that much power they will provide a detuned engine that can handle any fuel that idiots put in it, and then increase the output by like 5kw with each new model

What kind of temperatures do you need to keep it at? Could you use one of those home brew kits?

no you dont, all you need is a thermometer, a straw, zip tie freezeer bags, hot water and an esky ;)

I sous-vide almost all my red meat and a lot of other stuff at home, and I dont have a controller

Nah, would be less... even with the capability to have that much power they will provide a detuned engine that can handle any fuel that idiots put in it, and then increase the output by like 5kw with each new model

http://www.carsguide.com.au/news-and-reviews/car-news/hsv_supercharged_v8_tipped_to_top_w427

I cook most meat at 58c as per MY digital thermometer, and it comes out perfect every time, although my thermometer is pretty mangled as I have dropped it in the sousvide bath about 10 times and into a pot of 175c oil whilst deepfrying...

I usually get my steak from the vic market, leave it in the fridge until dinner and then throw it straight in a HOT griddle pan for like 60 seconds on each side to get some caramelisation on there, then throw it into some ziplock bags, suck out all the air with a straw and lock quickly.

drop it into the esky with the bag jammed in by the lid to hold the meat near the top of the water. set a timer for 45 - 60 mins and go watch tv or cook the other dinner bits

come back an hour later and chuck the bag on the bench to cool a little. and let the protien strands relax

cut the meat against the grain and throw on the plate with whatever sauce and sides I have made.

100% perfect medium rare rump steak that is as tender as all hell... every time

even the 427 would have only been say 300-320rwkw TOPS

I dont think it will be beating leigh's 370rwkw in a hurry, and it will be the TOP model @ $100k +

these are only guesses ofcourse

Also rwkw != manufacturer stated fly kw...

427 cubic inches = 7.0L

Bitch plz I could make 320rwkw with a few little mods to my little 2.5L ;)

mmmm but jelly of dat torque and power band... Super charged dyno graphs are boring... may as well go look at a wall, it's almost as flat.

inb4 leigh invites me to prinny...

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...