Jump to content
SAU Community

Recommended Posts

Any parts in particular you need or the whole thing? Might be able to get a bloke to go over it.

I'd prefer the whole thing if possible, that way I can double check everything and start ruling out causes etc

What was the damage?

$300, with a 2 month old GT Pumps actuator :D. Done about 70K kms.

Only thing is a snapped bolt which the thread doctor quoted $40 to drill out.

Not bad imo.

Waiting to hear back about some injectors atm as well :P

$300, with a 2 month old GT Pumps actuator :D. Done about 70K kms.

Only thing is a snapped bolt which the thread doctor quoted $40 to drill out.

Not bad imo.

Waiting to hear back about some injectors atm as well :P

still waiting on that injector guy? thats some slow responding.

$300, with a 2 month old GT Pumps actuator :D. Done about 70K kms.

Only thing is a snapped bolt which the thread doctor quoted $40 to drill out.

Not bad imo.

Waiting to hear back about some injectors atm as well :P

good price, wouldn't want to pay much more than that

still waiting on that injector guy? thats some slow responding.

tell me about it, -___-. if it doesn't work out, going to probably go with some id1000's. but dat price tag.

good price, wouldn't want to pay much more than that

yep! didn't want to spend more than 350, really. but now should hopefully flow 250+

much money, hipster boy

who is this hipster boy you speak of?

yeah same, must've been that odd occurance

I've heard they are planning to build one in Epping now too

Apparently, they're looking at building Costco somewhere on High St or around Epping.

And where Pipeworks is in Cambelfield, that's going to be Ikea opening early next year....

Stance? Probably not. Wouldn't mind being fairly aggressive, though. Wheels are still awhile away... not to mention coilovers as well.

Alvin, why not just go to the new Ringwood one?

Also not sure about those Kando turbos, could swear I've read some evooz thread(s) which do not recommend... Unless I'm thinking of something else.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...