Jump to content
SAU Community

Recommended Posts

You laugh now, but when I'm at a formal occasion with a shitty DJ and they need someone to drop Dre beats...I have something up my sleeve.

You probably tell that one to everyone who asks...
  • Like 1

Is there some sort of liquid in the tin when you take the spam out? Cos if so you could actually make a spam reduction

Surprised you have not tried it before

There is some sort of jelly that is slightly watery

Spam itself is oiled enough that you don't need a non stick or oil to cook it

Yup. Drop the wages. That'll make people want to work in the middle of a 50 degree desert

Problem is that people have built a lifestyle around the income & any pay is better than 0 pay.

Lot of small cap miners have gone into care & maintenance mode so there are a lot of people looking for any work.

I've been told I'll be changing to 8/6 roster from my 9/5 roster. Will be losing $20,000+

Problem is that people have built a lifestyle around the income & any pay is better than 0 pay.

Lot of small cap miners have gone into care & maintenance mode so there are a lot of people looking for any work.

I've been told I'll be changing to 8/6 roster from my 9/5 roster. Will be losing $20,000+

If my Maths serves me well then you're currently...

156-157k pa?

VWLBC leader

If my Maths serves me well then you're currently...

156-157k pa?

VWLBC leader

$20k is what hr has told in general for everyone in the office. No idea what it means for me. Could be more, could be less :P

Also your estimate would be excluding superannuation & bonus

$20k is what hr has told in general for everyone in the office. No idea what it means for me. Could be more, could be less :P

Also your estimate would be excluding superannuation & bonus

I think you've told me before actually but I forget...

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...