Jump to content
SAU Community

Recommended Posts

So I had a heater hose under the inlet go on me the other week in traffic. I completely cooked the engine with so much steam coming out the bonnet I had trouble steering down a slip road. It turns out with steam whistling through the system I cracked the overflow bottle. Have you got anything to replace the std reservoir. I may cut and tape up a breather.overflow setup that you can go to town on for me?!?!?

No Ti gear knobs sorry. Solid Ti billets are extremely expensive and rare.

I'm also not tooled to machine it.

No problem at all Roy.

Best to make something up from cardboard chuck it in a box and I'll redo it from alloy plate and send it back.

You shall see it tomorrow, I've just had no time to sit down and invoice anything recently.

About to be released are my new surge tank/pump setups with twin aero motive pumps inside the surge tank, sard style.

Not a problem I'll cancel the invoice.

If anyone wants an R33 undercar surge tank setup for twin 044's I've got one fabbed and ready to pressure test/ post off.

$330 inc gst plus postage charges.

You have a pm.

I don't get on here everyday, the reality is SAU accounts for 10% of my work so I don't always check threads and PM's daily. It's been weekly as of late.

My email is available. Best to contact me via that, or leave a return voice mail.

Not a problem I'll cancel the invoice.

If anyone wants an R33 undercar surge tank setup for twin 044's I've got one fabbed and ready to pressure test/ post off.

$330 inc gst plus postage charges.

Any pics of the surge tank Brad? Got a mate that might be interested in one.

  • 2 weeks later...

Good to see your happy with it.

It's a pretty trick way of doing the washer bottle filler on that can with the filler tube running through the catch can section .

From the top it looks like your putting water into the catch can ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...