Jump to content
SAU Community

Recommended Posts

nasty crash and good to see the guy was ok afterwards.

I have had my front suspension break after coming over the bridge at Oran park before, no rolling off the road but i reckon if it happened at speed on the straight i would be in the same boat and just a passenger.These were tein coil overs so it can really happen in any car either kit or something you buy from a major manufacturer.

I also was driving a car "somewhere" where we had been doing top speed runs in a 350kw light weight car and as i slow down and take a corner, the rear toe arm snaps and i come to a tire smoking spinning stop.

Just be careful to use quality parts and check over things regularly especially if you take it to the track often. Don't give up on your dream as i reckon building a kit car would be awesome :)

  • 2 weeks later...

Ultima is genuinely on my one day list of things. I have the bucket R32 fun club car. Now have the Sierra Cosworth to break down on me and leave me stranded in places. Now I just need a big house/garage to move on to one more project before the Ultima. That is getting a gig in Europe and bringing back the uber personal import :)

Likewise a bucket list item for me too. The recent engineering rule changes in NSW may put an end to that though which will be a shame.

Nothing too wild, just the basic kit, silver gel coat, black interior, AP brakes, 6.2L Chev engine around 300rwkw will be plenty

Always loved this pic speaking of Ultima's;

672%20Ultima%20GTR.jpg

If you look around you might be able to pick up someone else's 1/2 finished Caterham project. You'd be surprised how many people start projects like these and just leave them un-finished in a shed. You can pick them up cheap once they have been sitting a few years.

That Corvette is pretty cool. I love Vettes, but know them well enough to know many are garbage. From memory the 84 Vette has 185hp :( And being the first of C4s they are pretty rubbish. 89 - 94 is what I would be after.

But the biggest problem is housing prices in Aus, I cant afford a house for the toys :) Hence the plan to get to Europe with work, get the dream car. Import dream car and then when in 4-5 years when I am around 40 build a Caterham with S2000 running gear or Ultima, depending on cash, and what my 22yr old Russian bride prefers :)

yer, the emission regulations really hurt those Corvette , most people just take them off and be dune with them.

most cops have never seen a Corvette so it's not like a skyline.

If anybody is after a pretty well sorted Clubman, check this out;

Clubman

A friend is selling it. Makes 130rwk, weighs 550kg, does easy 1:08's at Wakefield and will go quicker.

Only reason for selling is that he bought a brand new one.... a MNR with a 'turbocharged' Hyabusa engine, dry sump, sequential box, digital dash etc = 220rwk and 500kg!!!

BTW if you contact me first, we can definitely do something about the price to make it very attractive...

Edited by SRS13

Has anyone looked at the STOHR vehicles? www.apracing.net.au

They look impressive for a track only option.

Anyone got an idea around cost? I see the closed wheel version also 'for lease' on my105...

Stohr's are quick, Adam Proctor won the Sports Racer series in his this year, however he had all of the best gear on his car (it won the DSR championship in the USA the previous year) and it had a modified motor when the Speads and the West's ran stock motors.

I have heard from people who run them and race against them in the States that they are somewhat more fragile than the West's and the Speads, as everything on the car has been reduced to the minimum size needed, and there are a number of parts like rod ends that are considered throw away items in the car.

  • 2 weeks later...

To be honest if you wished to walk the path of making a kit car, you couldn't get a batter start then Caterham (there are plenty of companies within australia that sell very nice replica kits for much cheaper). I've used to work for a mob that built them for the road and track and they are just awsome, they are very simple to put together with many people out there who will be more then willing to lend a hand, especially if you start getting some track time.

There are a few reasons why you should build a caterham well before trying to build something more crazy like an ultima/cobra/gt40, this is because it's relatively cheap to throw together (so if you give up like many others you haven't lost much), it will give you a very good understanding of what it takes to build a truely balanced vehicle, and it may very well be so much fun that you won't even want to move to something more expensive.

You have a large amount of engines to choose from depending on what you want, be it a nice NA like a 4AGE (a very common choice), or maybe something turbocharged like a SR20, or supercharged like a 4AGZE, or just go all crazy like and throw a Rotary in there. Actually there isn't many things you cant change on this car depending on what you want....

All in all i highly suggest you go for the caterham, then sell if off if you want more and then move onto your next project.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...