Jump to content
SAU Community

Recommended Posts

  • Replies 150
  • Created
  • Last Reply

Top Posters In This Topic

G'day C yar,

Perth is easy. I send them out COD post, so you only have ot pay for them when you pick them up - much safer this way. Nation wide postage is only $11. So the total cost will be $65 for the boot set, and $12 postage, totaling $77.

If your interested then I just need some sort of postal address (send me a PM with an address) and I can get a set out to you first thing Monday morning.

Any questions just ask away :P

Cheers

J

i just put in the boots and they are excellent. had a bit of trouble with the metal ring thing in the shifter which holds the boot in place. is there an easy way to make it sit properly as the leather (very nice) is a bit thicker than the old vinyl boot?

thanks again jay, they are must haves for all skyline owners (vinyl ones are crap!)

LOL - yepp, that metal ring is mega MEGA tight. Best thing to do is to (if you get stuck) is to pry the ring open just a touch - not much at all, but just a little bit.

All of the installs I've done I've been able to get the ring to sit right, but like I said, it's MEGA tight.

Glad you guys like them :)

J

  • 2 weeks later...

hey what and where is the wire frame for the gear stick bootie supposed to go? I don't think I even have a wire frame - the boot is all soft and mushy. Could explain why the top of the bootie sits so low.....

Anyone know where i can get a wireframe from?

King-kw13 - the wire frame sits right down the bottom of the boot and clips into the centre console from underneath.

You won't be able to see it from up top though.

Best thing to do is take the centre console out and have a gander and see what the go is.

J

  • 3 weeks later...

Hey Jay,

Just got a new gear knob to replace the old worn one and now the gearstick and handbrake boots look out of place.

Can you put me down for a set please.

I can come and pick them up from you when they are ready.

Cheers.

Originally posted by FunkBrother

Hey Jay,

Just got a new gear knob to replace the old worn one and now the gearstick and handbrake boots look out of place.

Can you put me down for a set please.

I can come and pick them up from you when they are ready.

Cheers.

No problems - I'll be ordering the new hide this pay day (thursday), so the next lot should be ready in about 2-3 weeks.

Seems your in canberra I can install them for you too. I've got it down pat now, takes me about 30 mins :D

I'll drop you a PM when they are ready.

Cheers

J

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...