Jump to content
SAU Community

Recommended Posts

These results give me a little tingly feeling in my balls thinking what the -5's will be like on my 30/26. Obviously provided it's setup as brilliantly well as yours is.

Hats off to you for your perseverance with it! Now the fun begins (driving it!).

Enjoy!

I think you need a 4wd dyno to do the final power output.

Do you know how much timing your running?? not sure if you know, when running tight squish you dont need the timing and if you put timing in it does not like it and what AFR is the tune to under full load?

I think you need a 4wd dyno to do the final power output.

Do you know how much timing your running?? not sure if you know, when running tight squish you dont need the timing and if you put timing in it does not like it and what AFR is the tune to under full load?

I can't answer that Bobby. I will find out specifics later on as the tune is not finished. it only had 9 runs or so. I dare say the AFR's will be a little richer then what you like ;)

As for 4WD dyno. Wanna spot me a run up on yours? :P

These results give me a little tingly feeling in my balls thinking what the -5's will be like on my 30/26. Obviously provided it's setup as brilliantly well as yours is.

Hats off to you for your perseverance with it! Now the fun begins (driving it!).

Enjoy!

Was lucky enough to take a mates 26/30 for a belt in Melbourne with dash 5's built by rp

300rwkw at 3000rpm

You will love it

These results give me a little tingly feeling in my balls thinking what the -5's will be like on my 30/26. Obviously provided it's setup as brilliantly well as yours is.

Hats off to you for your perseverance with it! Now the fun begins (driving it!).

Enjoy!

A fair bit of thought went into it all. I think the interesting thing is the cam duration. They are not massive lumpy grumpy things!

Having seen a sorted 30 with 5's on the same dyno.... providing it's sorted, you're in for something special ;)

What is the deficit going from rwkw to awkw in your experience Bobby?

300rwkw at 1400rpm less than Paul's is insane!!!

Didn't your mate Deimar do a test at CRD one day and there was 2 KW in it?

that member repetition looks to be a virus - i saw the same thing a few pages back.

sorry paul, ive even tried to edit my post & the site wont accept which is odd.

not sure about diemars experience but i did get some figures from crd when i asked him a while ago.

i'll try again clean up that shitty post of mine

were your cams dialed in?

Zero zero... We only did 9 runs from a totally new ECU and that's what it spat out.

They will have a tickle this week to see what it does. If it takes away from the midrange I don't want it!

Zero zero... We only did 9 runs from a totally new ECU and that's what it spat out.

They will have a tickle this week to see what it does. If it takes away from the midrange I don't want it!

I mean when the motor was build! since the cams are custom, its why i asked if cams have been dialed in to find zero? if not, i think its a good idea to know where the cams should be before playing with them

I mean when the motor was build! since the cams are custom, its why i asked if cams have been dialed in to find zero? if not, i think its a good idea to know where the cams should be before playing with them

We know where they are at zero zero. Yavuz set the loves up where he thinks they should be.... Not to say a degree here or there might make the difference.

Lets see what next week brings ;)

Geeeez looks like that port work on the head is doing the trick...

Who would have thought HKS knew what they were doing :/

But did they? its had the super special cams and springs changed in....

Edit: of course they know, but is it better than something that could of been done locally, as yavuz deemed it necessary to make these changes

Edited by jangles

Its hard to quantify any gains from port work without doing back to back tests. You really need to do a stock head with all the same bolt ons. Then try a worked head with all the same bits and compare results. However, not many people actually have the time or money to try that exactly.

Everyone gets tempted by changes when they have the engine apart lol.

Its hard to quantify any gains from port work without doing back to back tests. You really need to do a stock head with all the same bolt ons. Then try a worked head with all the same bits and compare results. However, not many people actually have the time or money to try that exactly.

Everyone gets tempted by changes when they have the engine apart lol.

Well nothing changed apart from the head, cams and an extra 0.5mm on the pistons. ECU did but meh

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
×
×
  • Create New...