Jump to content
SAU Community

Recommended Posts

These results give me a little tingly feeling in my balls thinking what the -5's will be like on my 30/26. Obviously provided it's setup as brilliantly well as yours is.

Hats off to you for your perseverance with it! Now the fun begins (driving it!).

Enjoy!

I think you need a 4wd dyno to do the final power output.

Do you know how much timing your running?? not sure if you know, when running tight squish you dont need the timing and if you put timing in it does not like it and what AFR is the tune to under full load?

I think you need a 4wd dyno to do the final power output.

Do you know how much timing your running?? not sure if you know, when running tight squish you dont need the timing and if you put timing in it does not like it and what AFR is the tune to under full load?

I can't answer that Bobby. I will find out specifics later on as the tune is not finished. it only had 9 runs or so. I dare say the AFR's will be a little richer then what you like ;)

As for 4WD dyno. Wanna spot me a run up on yours? :P

These results give me a little tingly feeling in my balls thinking what the -5's will be like on my 30/26. Obviously provided it's setup as brilliantly well as yours is.

Hats off to you for your perseverance with it! Now the fun begins (driving it!).

Enjoy!

Was lucky enough to take a mates 26/30 for a belt in Melbourne with dash 5's built by rp

300rwkw at 3000rpm

You will love it

These results give me a little tingly feeling in my balls thinking what the -5's will be like on my 30/26. Obviously provided it's setup as brilliantly well as yours is.

Hats off to you for your perseverance with it! Now the fun begins (driving it!).

Enjoy!

A fair bit of thought went into it all. I think the interesting thing is the cam duration. They are not massive lumpy grumpy things!

Having seen a sorted 30 with 5's on the same dyno.... providing it's sorted, you're in for something special ;)

What is the deficit going from rwkw to awkw in your experience Bobby?

300rwkw at 1400rpm less than Paul's is insane!!!

Didn't your mate Deimar do a test at CRD one day and there was 2 KW in it?

that member repetition looks to be a virus - i saw the same thing a few pages back.

sorry paul, ive even tried to edit my post & the site wont accept which is odd.

not sure about diemars experience but i did get some figures from crd when i asked him a while ago.

i'll try again clean up that shitty post of mine

were your cams dialed in?

Zero zero... We only did 9 runs from a totally new ECU and that's what it spat out.

They will have a tickle this week to see what it does. If it takes away from the midrange I don't want it!

Zero zero... We only did 9 runs from a totally new ECU and that's what it spat out.

They will have a tickle this week to see what it does. If it takes away from the midrange I don't want it!

I mean when the motor was build! since the cams are custom, its why i asked if cams have been dialed in to find zero? if not, i think its a good idea to know where the cams should be before playing with them

I mean when the motor was build! since the cams are custom, its why i asked if cams have been dialed in to find zero? if not, i think its a good idea to know where the cams should be before playing with them

We know where they are at zero zero. Yavuz set the loves up where he thinks they should be.... Not to say a degree here or there might make the difference.

Lets see what next week brings ;)

Geeeez looks like that port work on the head is doing the trick...

Who would have thought HKS knew what they were doing :/

But did they? its had the super special cams and springs changed in....

Edit: of course they know, but is it better than something that could of been done locally, as yavuz deemed it necessary to make these changes

Edited by jangles

Its hard to quantify any gains from port work without doing back to back tests. You really need to do a stock head with all the same bolt ons. Then try a worked head with all the same bits and compare results. However, not many people actually have the time or money to try that exactly.

Everyone gets tempted by changes when they have the engine apart lol.

Its hard to quantify any gains from port work without doing back to back tests. You really need to do a stock head with all the same bolt ons. Then try a worked head with all the same bits and compare results. However, not many people actually have the time or money to try that exactly.

Everyone gets tempted by changes when they have the engine apart lol.

Well nothing changed apart from the head, cams and an extra 0.5mm on the pistons. ECU did but meh

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...