Jump to content
SAU Community

Recommended Posts

held off putting it on here because i just wanted to rock up to a meet with a not so shitty r32 lol.

but here goes.

short term (shit to do now)-

-cut out all rust

-replace worn interior items with better condition bits and pieces

-wde body, paint etc

-replace RB20 with a working RB20

get it regesteredd

long term

RB26/30DETT

ANYWAY

i was whoring the vic wasteland like always when Rekin posts up a sale link to an 89 r32 sedan and suggested i purchase it. i took it as a joke but, 2 weeks later this happened...

IMG_0768.jpg

1989 R32 GTST, full GTR front end, GTR interior and a bride seat. motor was rooted but it was a good buy for 2 grand.

i was planning on just gutting it and making it a budget drift car but the more we stripped off it, the more i realised it was actually a fkn pearler for a 23 yr old ex drift car!

IMG_0769.jpg

IMG_0767.jpg

The tear down. i found $20 in change.

DSC05575.jpg

DSC05576.jpg

Glass out.

found a small rust hole, cut out and a new panel made up.

IMG_0829.jpg

Then, it became a 300zx

417493_2832452925848_1094891594_32188783_1936093329_n.jpg

cleaned and rubbed down the engine bay, and then i primered it.

552973_3733672823346_1321819556_33504007_1440241858_n.jpg

got some BL0 Greyish Blue pearl put into a couple of cans and painted the engine bay.

more to come..

I bought these....

549374_3733674223381_1321819556_33504008_1593983528_n.jpg

and this

563645_3782706369154_1321819556_33518687_2109935123_n.jpg

and this (in AWESOME condition)

528010_3782720489507_1321819556_33518689_1009589091_n.jpg

painted the engine bay

427842_3745741565057_1321819556_33510448_1205976150_n.jpg

and picked up some genuine R32 sedan plastic rear pods (THANKS RTUNE!)

374024_3781217051922_1321819556_33517425_926288548_n.jpg

as she sits now, new rb20 should be in by this week end, interior in by the week end after that and then off she goes for the bulk of the body work.

fun times and sore wallets ahead.

318154_3800571935782_1321819556_33528176_1674304092_n.jpg

what condition is the roof in?

I bought the LAST glass in existance, the motors are still available though. since you have the car down pull that roof , strip it and clean it out. doing that made a world of difference to mine.

motor part # is: 91295-01U14. its a $500 bit as used in a S15.

i know you did LOL, the sunroof is actually very very clean, getting the motor rebuilt next door (mates rates ftw)

the only downside is the fibreglass ring around the sunroof is chipped etc, panelbeater is going to repair that little strip.

yep you have the glass style that I bought. the early one is steel and rusts. I would still tear it down and clean the crap out of the rails. that part of the reason they fail.

nice one lad. they the same rims as you had on the 34?

thanks, yep, the 32 is on the rotas now.

Looks good

are you going to do anything to the rear doors to meet up with the wider gaurds?

yep, comes with the door panels. same kit as this.

5445785440_ae8055a90c_o.jpg

just bought some goodies

stock GTST airbox OMFG WTF yeah, took me that fkn long to find a complete one...

excedy oem replacement clutch and spigot, no point buying a heavy duty when im going to drop a 2630 + twin plate and 5 speed 33 box behind it.

interior odds and ends (bought a big box with a rear seat, carpet, trims etc) should arrive on monday. pumped!

  • Like 1

UPDATE

got bored one night and mocked up the fenders.

156184_3831874038315_1321819556_33540887_581823179_n.jpg

398320_3831871798259_1321819556_33540886_1596074070_n.jpg

then my carpet and back seat came so i put it all in

457184_3853739864947_1321819556_33551621_400455922_o.jpg

cute pink clutch, ended up going heavy duty :D

558468_3856913744292_1321819556_33554145_85370965_n.jpg

after a lot of cursing in various languages, we got this engine in.

559428_3864839622434_1321819556_33558058_1768124653_n.jpg

car goes to my mechanic next week so he can get her started, and then off to the panel shop.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...