Jump to content
SAU Community

Recommended Posts

  • Replies 126
  • Created
  • Last Reply

Top Posters In This Topic

I've done heaps of divided turbo pipes, they do work but having done so many I also found a trick with the divider plate.

I leave a small section of the front turbos air path in plated, it allows some of the front turbos air to swirl around into the rear turbos path.

A customer of mine who is a fluid scientist type guy explained how making the front turbo swirl around the inside of the pipe before merging with the rear turbo helps promote a lamina flow and draw the air away from the compressor housing thus reducing the shuffle.

The mod does seem to improve the issue on all the cars I've ever done one for.

Can't hurt to give it a go.

Risking,

So if mine was to shuffle for some strange reason (people say it should be OK)....then to what level would the TT pipe mod cure the shuffling? Would it still be there a little bit or would it completely disappear?

Everyday I'm shuffling :D lol sorry had to throw that one in...

I've currently got t517z turbos and no TT pipe mod, no shuffle

I had the impression shuffling comes from bigger turbos (gtr-s, -10 etc)

LOL I've been waiting for that :D

Yeh same here. It's meant to happen with big efficient BB turbos that spool up a bit too much air down low and cause surging and stalling out of each other in a seesaw/back and forth fashion. That's how I understand it anyway :P Sort of similar to that shhh-shhh-shhh-shhh that it does when you back off the throttle very slowly at lowish RPM and on boost. ....i think.

I'm thinking I'll be fine.

Everyday I'm shuffling :D lol sorry had to throw that one in...

I've currently got t517z turbos and no TT pipe mod, no shuffle

I had the impression shuffling comes from bigger turbos (gtr-s, -10 etc)

What ECU do you have?

Ah damn, so there's probably a 50-50 split of people who've experienced shuffling and those who haven't with -9's

Ah there is one person in the thread, everyone else hasn't had an issue.

Not sure how that is a even split.

newb time... what exactly is shuffling and i'm assuming it's a bad thing from how this thread is referring to it?

As far as I know, shuffling is a thing where the two turbos will try to stall each other out down in low rpm ranges because they're creating too much air than what the engine can swallow. Both turbos are trying to force more air into the one overhead collecting pipe and that pressure will not always go to the intake mani but back down the other turbos xompress

Ah damn iPhone!

....was say that it will instead go back down the othe turbos compressor out let thus causing it to momentarily stall out. It's meant to happen with bigger, efficient bb turbos where the two turbs create too much boost down low...similar to surge. It's meant to give off a shoo shoo shoo sound when it happens...hope that helps ;)

I was thinking shuffle would happen easier with the smaller BB type turbs like the -7,-9 where they make boost very early in the rev range, say 2k-2.5k and the engine just simply cannot ingest that amount of air, and with the oem journals and the -5,-10 that do not start to make positive pressure so early it would not really be a problem.

With the -9s crusing along on 5th flat roads, just easing on the throttle at 2k ish is enough to make +ve pressure and you get shuffle. Ive never driven a car with -5s, but under the same conditions, does it make +ve pressure to induce shuffle?

I was thinking shuffle would happen easier with the smaller BB type turbs like the -7,-9 where they make boost very early in the rev range, say 2k-2.5k and the engine just simply cannot ingest that amount of air, and with the oem journals and the -5,-10 that do not start to make positive pressure so early it would not really be a problem.

With the -9s crusing along on 5th flat roads, just easing on the throttle at 2k ish is enough to make +ve pressure and you get shuffle. Ive never driven a car with -5s, but under the same conditions, does it make +ve pressure to induce shuffle?

That's all very true, just curious why in this particular thread you're the only one experiencing these problems? The majority seem to say that there're no issues with the smaller turbos in the GT2860 range.

Bearing in mind every set up is different and there are many factors that have to be considered eg. actuator preload(mine are f*ck tight) boost controller settings and as some have said tuning.....and hell, diff ratios for all I know

Also mine is not in a gtr, but everything is set up as normal beside for a 2.5" hot pipe from TT pipe to intercooler which I guess could be contributing.

Either way no biggie. There are some here who get it with oem turbs....

I've got gtrs, shuffle under higher load.

Went to a bigger exhaust, problems better.

Getting a modded TT pipe from risking soon, will report how that goes.

I've got a set of hks gt-rs on my 2.6l. 441awkw @ 24psi no shuffle at all. :)

Have had hks 2530s and no shuffle either all of this with no modification to twin turbo pipe or any other..

How did you get it to stop?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...