Jump to content
SAU Community

Do I Need A Transmission Cooler

ChrisB

By ChrisB,
in Four Door Family & Wagoneers

 Share

Recommended Posts

ChrisB Rising Star

ChrisB

Posted
Posted (edited)

So i drove from up to Lake Mountain today and took the kids to the snow.

Between Healsville and Marysville i put the stick into Manual and discovered that the transmission would not shift up or down on demand and the display just sat on "4"

In "D" mode it was still working perfectly and shifting automatically. It just would not shift manually.

I pulled over in Marysville and it was working in Manual again. (without even having to re-set the ignition)

I'm thinking it was some kind of safety feature on the transmission computer and perhaps the transmission was getting hot due to all the hill climbing and low gear work.

Down hill all the way home and manual shifts were perfect.

Has anyone else experienced this issue?

Should i get a transmission cooler and if so how much, where from and how to?

Car is an M35 ARX

Cheers in advance and hope to see you all soon on the next cruise.

Chris

Edited by ChrisB
Link to comment
https://www.sau.com.au/forums/topic/403889-do-i-need-a-transmission-cooler/
Share on other sites
Commsman Veteran

Commsman

Posted
Posted (edited)

Yes, get a trans cooler. Costs about $100 & available from auto stores everywhere & E-bay etc. Simple to fit. Just look first at how much room you have & get one to suit. It doesn't need to be very big to be effective.

Edited by Commsman
pbk1776 Mentor

pbk1776

Posted
Posted

I'm getting The same experience Mostly long drives. done the oil tranny change, it helps.

If I get one - I might get one from eBay without the hoses and fittings, might get them from earls just to make sure that I can mount it where suitable

XRATED Veteran

XRATED

Posted
Posted

Don't bother with earls fittings and 'performance hose'.... the lines arn't under that much pressure. PWR make some great trans coolers in most usable sizes. They're available from repco etc - the whole lot should come in under $120 including more hose if needed. The PWR kit comes with hose clamps and mounting fittings etc. Make sure you buy trans hose if you need to buy extra.

I'd sugest plumbing it in after the/any factory coolers (not sure on your m35, you may have a small air to air cooler or a warmer/cooler as part of the radiator) and using a cooler core that has slightly larger inlet/outlet fittings than the stock cooler (just reduces any pressure loss across the core).

I'd also change the trans fluid too...

This is what I did with my C34, it works a treat with my modified auto trans.

Cheers

Justin

theferris Rookie

theferris

Posted
Posted

I learnt the hard way in how valuable an oil cooler is the other day in my Jeep. Going over a big set of hills, just started blowing smoke. Didnt loose any function in the box to begin with. Now it doesnt have 4th and reverse is almost gone. It did something similar to yours about a year back, thought it was a computer problem, swapped it out and didnt have a problem until the gearbox blew its load everywhere.

ChrisB Rising Star

ChrisB

Posted
  • Author
Posted

Guys,

Great Information thanks.

The Transmission was flushed and filled with Mattic S a few months ago.

I will check the colour but hope its OK.

When i get a transmission cooler i hope it will only need topping up.

When plumbing in the cooler, should i put it in series with the radiator or disconnect the trans hoses from the radiator?

Commsman Veteran

Commsman

Posted
Posted

I put mine in series with the radiator so that the warm oil flows thru the a/m cooler then onto the radiator. This means the trans should get up to temp quicker as the oil is warmed by the radiator before it flows back in. It also means on really hot days it will take some load off the radiator by cooling the trans fluid a bit before it gets there.

Running it independant of the radiator will work OK as well (no heat load on the radiator at all), but may take a little longer to get up to good operating temp.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

I fitted one of these thermostats inline with my trans cooler, it allows the transmission to warm up to operating temp before flowing through the cooler, and will limit the amount of cold 'issues' you will have when you just plumb it in.

http://www.ebay.com.au/itm/LONG-OIL-THERMOSTAT-COLD-CLIMATES-OC-708-4739-/370626344630?pt=Motors_Car_Truck_Parts_Accessories&hash=item564b0d36b6#ht_820wt_1159

The hoses may be a different size, I had to use adapters for the hoses, but it works well.

Mr 20Valve Rising Star

Mr 20Valve

Posted
Posted

I put mine in series with the radiator so that the warm oil flows thru the a/m cooler then onto the radiator. This means the trans should get up to temp quicker as the oil is warmed by the radiator before it flows back in. It also means on really hot days it will take some load off the radiator by cooling the trans fluid a bit before it gets there.

Do you remember which hose between the gearbox & radiator was which?

I was planning on hooking up my trans cooler the exact same way...

PN-Mad Grand Master

PN-Mad

Posted
Posted

From memory. If you are lying under the car looking towards the rear.

Top is pressurised flow from the trans, bottom is the return to the trans. That's the hard lines that end just near the sump. To make sure, just pull the bottom line off the hard line, and put it in a clean 1 litre bottle. Get someone to turn the car on for only 2 or 3 seconds. Should pump out 500 ml or so. You can add the fluid back in via the dipstick.

Daleo Grand Master

Daleo

Posted
Posted

With a NA c34? Towing a rally car? Might be a bit over zealous there.

So 750kg of trailer, and 1200kg of car; how early will you be leaving for an event? Any hills along the way?

Not my pick for a tow car; that's for sure.

theferris Rookie

theferris

Posted
Posted

With a NA c34? Towing a rally car? Might be a bit over zealous there.

So 750kg of trailer, and 1200kg of car; how early will you be leaving for an event? Any hills along the way?

Not my pick for a tow car; that's for sure.

Ahh you know, figured it weighed in pretty similar to a V6 Holden and the Straight 6 Cherokee it wouldnt be too bad.

And as for time it would be day before and NZ doesnt have many flat roads.

Is more of a long term possibility then needing to go to an event next week.

I still have to rebuild and sell my Cherokee and move to a more car friendly place before I consider it.

Daleo Grand Master

Daleo

Posted
Posted

Ahh you know, figured it weighed in pretty similar to a V6 Holden and the Straight 6 Cherokee it wouldnt be too bad.

And as for time it would be day before and NZ doesnt have many flat roads.

Is more of a long term possibility then needing to go to an event next week.

I still have to rebuild and sell my Cherokee and move to a more car friendly place before I consider it.

Yeah, weight of the Stagea is probably similar to a V6 Holden; the torque from a NA RB25 however, no where near similar. :no:

You'll be giving the clutch a hiding just to get it moving.

RB25/30 with a turbo? Now you're talking. :whistling:

lilcrash Veteran

lilcrash

Posted
Posted

on the towing note - ive towed a few heavy loads (64 besser bricks + trailer, car trailer + car), and my car(c34 rs4s) tows beautifully, only issue ive had was clutch slippage reversing the car trailer of a steep driveway, only slipped for a second before all 4 wheels started spinning. but definatly wouldnt recommend with an na.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...